DEAR TIM: Eight years ago, I had a new asphalt shingle roof installed on my 55 year old home. Leaks recently started to appear in several areas of my home and upon inspection, roofing nails actually had backed out and popped through the shingles. Why did this happen? I hammered the nails back down and applied roofing cement over the holes. Is this the correct thing to do? Is there a permanent way to patch the holes in the face of the shingles? John D., Atlanta, GA

DEAR JOHN: Roofing nails that seem to defy gravity are more common than you might think. In fact, it has even happened on my own roof. There are all sorts of reasons why nails back out of seemingly solid wood, but perhaps the most common reason is that the nail did not get a good bite into the wood when it was first driven. It is vitally important that roofing nails of the correct length were used to secure the shingles. The sharp tip of the roofing nail should completely pass through and extend approximately 3/8 inch past the underside of the roof sheathing.

It is entirely possible that your roof sheathing might consist of numerous tongue and groove 1x6 boards. This was a very common roof sheathing product in the 1950's. Every 5.5 inches there is a horizontal seam where two 1x6s interlock. If the roofing nail happens to penetrate the sheathing along this seam, there is very little solid wood to hold the nail. In fact, the roofing nail can actually crack of the thin tongue along the seam. If this happens, there is virtually nothing holding onto the nail.

This same thing can happen on roofs that have large 4 x 8 pieces of plywood or oriented strandboard sheathing. Nails that hit weak spots in these products or along the seams where one sheet meets another are highly susceptible to backing out.

Each day and night your roof and the sheathing beneath it go through a heating and cooling cycle. Add to this the changes in humidity and you can see that the wood sheathing not only expands and contracts but it can also do so with astonishing frequency. This movement can slowly and forcefully push a nail up and out of the wood. The movement is very slight each day, but it does indeed happen. In the most severe cases, as in yours and mine, the head of the nail actually breaks through the top layer of shingles. Many people have nails that have backed out, but they simply see a hump in a shingle.

The repair method you followed will not be permanent. Since you did not relocate the nail, it continues to have minimal or no holding power. The nails should have been removed and relocated about one inch higher in an attempt to find solid wood. If you can enlist the help of someone, they might be able to go inside the attic and see the pesky nail as you pull it out. They can communicate with you and tell you which direction to go to get away from a seam, crack or a knot in the roof sheathing.

The asphalt cement you applied over the hole in the shingle is also not permanent. The sun's ultraviolet(UV) rays break down the asphalt and cause it to age prematurely. The colored ceramic granules that cover asphalt shingles, among other things, serve to shield the asphalt in your shingles from these harmful UV rays. At the very least while the asphalt cement was fresh, you might have collected some loose granules from a gutter to broadcast into the sticky asphalt cement.

I feel a better way to patch the hole is to do so from under the shingle. Cut a four by two inch rectangle of regular 15 pound felt paper and fold it into a two by two inch square. Lift the damaged shingle up and apply a half-teaspoon dab of asphalt cement directly over the nail shaft hole. Press the piece of felt paper into the fresh cement making sure the crease in the paper faces up towards the roof.

The shingle can now be laid back flat on the roof. If it is not flat, apply additional asphalt cement under the lower edge of the shingle and press down until the shingle behaves and lays flat. The hole in the surface of the shingle can be carefully patched with a small amount of asphalt cement. Liberally apply loose matching colored granules to the cement and press them into the sticky black goo. Once you are back on the ground I doubt you will be able to see the repaired hole.

Repairing shingle leaks is very easy. The trick is to work with the shingles when they are warm. Cold, brittle shingles can crack easily. Use a wide, flat pry bar to break the seal between individual shingles. Slide the pry bar up under the shingle and it will eventually allow you to gently bend the bottom of the shingle up. Do not over bend the shingle as it can crack even if it is warm.

If you can't find any loose granules at your home, you can possibly get them for free at any business that sells shingles. They have thousands of them scattered on the floor or around the pallets where shingles are stored. Roofing manufacturers actually sell buckets of new granules if you need them in larger quantities.

Still Need Help? Type Your Keywords Here: (examples: drywall repair, pilot light goes out, poor lot drainage, crown molding guide, etc.) Your Facebook friends would love to know how this column helped you solve your problem. Type a quick comment of what you discovered here at AsktheBuilder.com. Thanks!

Comments: Welcome! I, Tim Carter, don't answer questions here. If you post a question here in the Comments Area, perhaps another visitor will help you. You need to go to the Ask Tim page if you want a question answered. Once there, look closely at how many weeks behind we are. Please be patient as you use this free service. If you have an emergency and need to talk to me, there is an option there for you. Matt 27 Nov 2007, 12:59 Good Info, easy to follow and read. Rose 03 Dec 2007, 10:13 Good day Please send me a short message on how roofing nails and wire nails are made, I am writing a project so I want to explain to people how to make nails. Regards Rose AsktheBuilder 03 Dec 2007, 10:53 Simple. They all start as a giant spool of wire. The wire is fed into a machine that cuts off a small length, smashes the top to create the head and then makes a point at the end. Richard 28 Dec 2007, 16:59 Are your comments above also applicable to '35 year glass fibre' shingles laid on 1/2 inch OSB? Initially my roof was great when laid in 1993 but now it consistently leaks in two valleys formed between a garage whose long axis is at right anles to the main roof. I find popped nails in many places throughout the roof but it only leaks in the valleys. I am told that the valley flashing extends approximately 9 inches either side of the centre crease. Is this enough? AsktheBuilder 28 Dec 2007, 17:08 Richard, Go read the special column I have about how valley shingles MUST be cut to prevent leaks. See if your shingles have the little tip cut off. Brian 13 Mar 2008, 19:38 My home is 1.5 years old with a high quality asphalt shingle. Combined with the steep pitch of my roof I have been told the roof could last 30-40 years. It already leaks. I have nail pops ALL OVER. Does the roof need to be replaced? AsktheBuilder 15 Mar 2008, 08:33 Brian, You need the roof inspected by a real professional. This person can tell you if the roof was installed according to specs. You can also ask the Manufacturer to send out one of their regional reps. Nancy 31 Mar 2008, 06:52 I have a roof vent that ripped out about a 8' long section due to high winds. So roofing nails don't work when i try & re-nail the metal vent back in the same place. Since the holes are pre-set on the metal vent, I cant nail it down in any other place but where the holes are. What to do? AsktheBuilder 01 Apr 2008, 05:07 Nancy, Who says you can't nail it in another location on the flange??????? I am sure you can and you simply slide a piece of tin under the flange at the old hole locations, then caulk the holes on top of the flange. Victor Peters 17 Apr 2008, 03:22 I have champion Home that has litterally hundresd of these nail popping problems. I used silicone for a temp fix. But would replacing the regular nails with ringshank help in the OSB      View all comments *Name: Email: Notify me about new comments on this page Hide my email *Text: Security Image: Security Image Text:   Remember, Tim Carter doesn't answer questions here in the comments. You need to go to the Ask Tim page.