DEAR TIM: We have Trex decking that we put down in 2008. The Trex lumber has developed dark spots all over it. It started with a few and has multiplied over the two-year period. What, in your opinion, is causing the spotting? How can it be removed? Is there anything that can be done to prevent the ugly spots? We purchased this material thinking it would be maintenance-free and are very unhappy. Trish A., Bristol, CT

DEAR TRISH: You’re not the first consumer to reach out to me with this issue about Trex composite decking. You’ll not be the last. What’s more, I have personal experience with this decking material as it’s on two very large decks and my front porch at my New Hampshire home. I didn’t install it, the previous owner did when the house was built eight years ago.

My own Trex decking has spotting issues, algae growth, and uneven coloration issues. As you might imagine, I’ve got lots of experience with decks of all types being involved with them for over 36 years. Believe it or not, it’s highly unlikely that the decking material itself is causing the entire problem. The issues you’re having can happen on just about any decking material. However, your deck and mine might be more prone to issues for a number of reasons.

The dark spots on your deck, based on the photo you sent me, appear to be mold and mildew. This spotting can happen on any deck. Mold and mildew feed on natural materials such as wood fiber, natural sugars, dirt, dust, grease, oils, and food. If you have trees or other vegetation near your deck shading the decking, these might be manufacturing airborne sugars that coat the deck.

Some trees produce more of this than others. Perhaps you’ve seen this sap coat a freshly cleaned car that’s parked under a tree. The spots show up easily on the high-gloss surface of a car paint job, but are tough to detect on a flat finish such as your deck boards. The sugars can float through the air from trees near the deck.

The mold and mildew can also feed directly off of the wood fibers in your Trex decking. The FAQ page at the Trex web site clearly states that “ ... most of the materials used in making Trex are recycled ...” They go on to state that “ ... the materials are carefully processed to ensure the highest level of quality and performance.” However, it’s possible that mold and mildew spores could be already present in the raw recycled wood material that’s used to make the decking.

Add to this the possibility that the wood fibers in the decking may not have any preservative added to them at the factory. If this is the case, then the wood fibers, or concentrated areas of them in the decking could easily support the growth of mold and mildew. I see it happening on my own Trex deck.

A visit to the Trex decking web site reveals they have a comprehensive cleaning guide that may help you. They are quick to point out that a powerful pressure washer, one that delivers a pressure stream greater that 1,500 pounds per square inch (psi), is to be avoided. What’s more, never hold the pressure wand closer than 12 inches from the decking surface. A concentrated stream of high-pressure water can erode the wood fibers that’s in the decking.

No deck is maintenance free, not even the expensive composite decks. All will have to be periodically cleaned from time to time.

I personally have had the best luck cleaning my Trex deck with oxygen bleach. This is a powder that you mix with water. It works to clean any decking material. The oxygen ions in the solution readily clean mold, mildew, algae and any food you may have spilled on the deck. What I like about oxygen bleach is that it removes the gray coloration from the small wood fibers in my Trex making it look like new. The sun’s UV rays cause the wood fibers in the decking to turn gray.

I apply the oxygen-bleach solution and allow it to sit for 15 minutes never allowing it to evaporate. It’s best to work early or late in the day when the decking is in the shade. After the wait period, use a stiff scrub brush to clean the decking. Rinse with clear water from a garden hose. You’ll be amazed at how clean and new the decking will look.

Some spotting you see may not be mold or mildew. I see that on my own Trex decking. I’ve studied this very closely with a magnifying glass and believe it to be a manufacturing characteristic. It appears that the dark spots are areas where there is a higher concentration of the recycled colored plastic.

If this is the case, it make sense that over time you’ll see uneven coloration as the thin film of plastic wears off those areas nearby that have more wood fibers than plastic.

I’ve visited a manufacturing plant where composite decking is made and saw how the wood fibers and plastic are kept separate until just before they enter the extruding machine. Although the manufacture makes every effort to mix the ingredients evenly, I can see how it’s possible that this doesn’t always happen.

Still Need Help? Type Your Keywords Here: (examples: drywall repair, pilot light goes out, poor lot drainage, crown molding guide, etc.) Your Facebook friends would love to know how this column helped you solve your problem. Type a quick comment of what you discovered here at AsktheBuilder.com. Thanks!

Comments: Welcome! I, Tim Carter, don't answer questions here. If you post a question here in the Comments Area, perhaps another visitor will help you. You need to go to the Ask Tim page if you want a question answered. Once there, look closely at how many weeks behind we are. Please be patient as you use this free service. If you have an emergency and need to talk to me, there is an option there for you. Ernie 11 Oct 2010, 13:47 Trex owners should be aware that there have been 2 class action lawsuits against Trex. One for dark spots (I believe it is for mold) and one for severe flaking & deterioration of some TREX products in a VERY short period of time (2 years). The latter one has been settled so payments are available to owners. (pennies on the dollar, but better than nothing). I have not followed the first one because it does not affect my Trex products. Good luck. Albert Lattimore 15 Nov 2010, 01:52 It really doesn't seem like Trex products are to blame for any of the problems people accuse them of. If you don't clean your deck for 4 years, then it will look crappy! It's just common sense. That isnt the fault of the building materials. Trex puts out a quality product than is environmentally friendly--that's rare. r carter 04 Dec 2010, 13:40 new trex has wood grain pattern. i am trying th match trex boards that have a grooved surface that are a few years old. do you know where to find it? Fianna Hill 13 Jan 2011, 05:44 There is a lot to like about Trex's decking products. They are environmentally friendly, which is good thing in this day and age. But more importantly, their products are just top notch--and they last a long time too. I agree with Albert, above, that if you don't clean your deck but once every four years, you can't very well blame the manufacturer for how bad it looks.      View all comments *Name: Email: Notify me about new comments on this page Hide my email *Text: Security Image: Security Image Text:   Remember, Tim Carter doesn't answer questions here in the comments. You need to go to the Ask Tim page.