Q&A / 

How to Patch a Plaster Wall

I don't know how many older homes there are on Long Island, NY that have traditional plaster, but I'm willing to bet it's in the tens of thousands. You can still get real plaster installed in a new home, but it's more expensive than drywall that's now the belle of the ball.

If you own an older home that's got real plaster walls and ceilings, you'll discover quickly that traditional drywall premixed joint compound will not work well to fill larger holes. You need to use different materials and fortunately they're readily available and not too hard to work with.

Degree of Difficulty: hammer-3-5

Step One: Gather the following supplies:

  • one 50-pound bag of Structolite
  • one 25-pound bag of Durabond 90 dry-setting joint compound

Dust off all of your normal drywall finishing tools:

  • mud pan
  • 6-inch taping knife
  • 10-inch broad knife
  • grout sponge
  • several buckets
  • a hand pad sander
  • a carpenter's framing square

Step Two: Remove any loose plaster from the area you're going to repair. Very old homes had thin wood lath strips nailed to the wall studs and ceiling joists. Homes constructed just before WW II and after, usually had 3/8-inch by 16-inch by 48-inch long pieces of plaster lath board that covered the wall studs and joists. The plaster lath was the precursor to larger sheets of drywall used in today's new homes and remodeling jobs.

Step Three: Be sure the wood lath strips are securely nailed to the wood framing. The same is true if you have plaster lath. Both of these are the foundation to the plaster and they must be sound. If you have to install new plaster lath, you can purchase 3/8-inch thick drywall and cut it to fit the opening you have.

Step Four: Traditional plaster was a two-stage process where the master plasterers put on a base coat of sanded plaster that was a mixture of medium sand, hydrated lime and a little Portland cement. The addition of the Portland cement is one reason plaster is so hard because, in essence, you have a thin sheet of concrete on your walls and ceilings. Your new base coat to fill deep holes will be the Structolite.

Step Five: Mix the Structolite as instructed on the label of the bag. Make sure the hole you're filling has all loose material out of the way and dust off the area to be patched. I've always had great success spritzing the area to be patched with some clear water to slightly dampen the hole. This will help the Structolite bond to the old plaster.

Step Six: Use your smaller taping knife to fill the hole in the plaster. You want the finished surface of the sandy Structolite to be 1/8-inch below the surface of the finished plaster. Use the carpenter's square to span across the good plaster on the sides of the hole to ensure there's a gap between the square's edge and the fresh Structolite.

Step Seven: Allow the Structolite to set up. Depending on the temperature, it can get stiff within a few hours. Read on the label of the bag when you can safely coat over it with the finish material. You might want to do this within eight hours or less. The sooner you do, the better chemical and mechanical bond you'll get between the Structolite and the Durabond 90.

Step Eight: The Durabond 90 is a powder you mix with water. It's not as hard once cured as true white-lime plaster, but I doubt you can work with real plaster. It's a craft and requires practice and training. The Durabond 90 will produce a gorgeous smooth finish that will match the existing plaster and it's sandable. Real white lime plaster can't be sanded it's so hard.

Step Nine: Mix the Durabond 90 with cold water to extend the working time. You apply this as you would normal drywall joint compound. Mix it to the consistency of warm cake icing. Try to put it on over the Structolite so it's extremely smooth and free of surface defects. Be sure it's in the same plane as the surrounding plaster. You can always add more, but remember it's hard and messy to sand off extra.

Summary: The Durabond 90 can be wet sanded as it starts to harden in about 90 minutes after mixing. You can use the grout sponge to do this. It just requires very light strokes or circular rubbing. If you try to sand too early, you'll make an indentation in the Durabond 90. Once you get the hang of working with the sponge, you'll love how you can sand it without dust. Use your pad sander as a last resort if you mess up the wet-sand process.

Column HT041

SPONSORS / 

One Response to How to Patch a Plaster Wall

Leave a Reply

Your email address will not be published. Required fields are marked *