How To Replace Paneling With Drywall

Posted on by Tim Carter

Drywall Over Paneling TIPS

DEAR TIM: My wife and I bought a 35-year-old home that has thin wood paneling in several rooms. We don't like the dark paneling and want to make the room lighter in appearance. We're thinking about drywalling the rooms, but the paneling is so much thinner than regular drywall.

If I install drywall, it will stick out past the door and window jambs. What can we do to solve this problem?

To add insult to injury, the height from the floor to the ceiling is 8 feet 8 inches. Should we cut 10 foot long pieces to fit and install them vertically? Is there some other option to make the room look great without all the work? Jeremy S., Green Bay, WI

DEAR JEREMY: I'll bet you were perplexed when you pulled off that first piece of paneling to see how thin it was. I remember that happening to me many years ago.

Stop! Options

The great news is that you have several options and I urge you to stop removing paneling immediately until you test at least one of my ideas. Since you've already considered removing the paneling, what I propose is not going to create problems.

In reality, I believe I can save you lots of sweet moola (money) and days and days of time.

CLICK HERE to get FREE & FAST BIDS from local painters that can do the quick painting test on your paneling.

Stain Solver Cleaner

Oxygen Bleach

Stain Solver is MADE in the USA with USA ingredients that are food-grade quality. CLICK THE IMAGE to order some NOW.

As crazy as this sounds I want you to clean one wall of the paneling with Stain Solver oxygen bleach, soap and water and rinse it with clear water.

The Stain Solver oxygen bleach will do an amazing job of removing any wax or polish previous homeowners may have applied to the paneling.

Stain Solver is Made in the USA with USA ingredients. It's certified organic. It's a fantastic de-greaser. You'll need this in case the paneling has an oil-based polish on it.

Paint Is Light

Your goal is to lighten up the room. You can achieve this without removing the paneling.

All you have to do is paint the paneling a nice off-white color.

Be sure the paneling is free of any wax or polish before you paint. If you don't do this, the paint will peel in the future.

Use a primer for bare wood. If you're using a new paint that says it contains the primer read the label to ensure it's made for bare wood.

Finish Paint Immediately

If you use a traditional primer, the label will tell you how soon you can apply the finish coat of paint. Follow those directions.

Assuming the primer is water-based, you can usually apply the finish paint within two hours.

Behold The Beauty

The purpose of painting this one wall as fast as possible is to do a proof of concept.

I think you and your wife are going to be quite surprised how good the painted paneling looks. To really get a good feel, I want you to move some of the furniture up to this wall and hang one or two pictures.

Vertical Lines Add

You may be shocked at how good this one painted paneling wall looks. The vertical lines in the paneling can add character and depth to the otherwise flat surface you'll get when you drywall.

Over the years on several jobs I did this for customers and each one was stunned by how good the painted paneling looked. They were originally going to remove it like you're thinking of doing.

Fill The Grooves

If the vertical lines or grooves in the paneling bother you or your wife, you can also fill them with spackling compound. It may take several attempts to get the cracks filled so they are perfectly even with the paneling, but it is far less time than you will spend installing and finishing the new drywall.

You can use a newer spackling that has paint primer built into it saving you a step I mention below.

spackling with primer

Here's a pretty cool spackling compound. It's got paint primer built into it. This saves you time and money. CLCK THE IMAGE NOW TO ORDER THIS SPACKLING.

Special Bonding Primer

If you use spackling without a built-in primer, you must prime the paneling with a special clear bonding primer/sealer that will take care of both the texture difference between the smooth paneling and coarse spackling and the vast porosity differences between the two materials.

Clear Bonding Primer

This is a great clear bonding primer. CLICK THE IMAGE NOW TO ORDER IT.

You apply this special bonding primer / sealer after you've filled the grooves and sanded them.

If you don't use this special primer/sealer, you may see the vertical lines even after the finish paint is applied.

CLICK HERE to get FREE & FAST BIDS from local painters that can do the quick painting test on your paneling.

Must Do Drywall

If you and your wife are stuck on drywall, then you need to choose the thickness you want and make adjustments to the jambs at each door and window after the drywall is installed.

Drywall Over Paneling

Look at the window jamb and notice how it is recessed from the face of the added drywall. The natural-colored wood strip with the finish nail has been added to extend the window jamb so it is flush with the drywall. The wood strip would normally continue all the way down to the window sill but was left short for this photo to illustrate why it needs to be added in the first place. ©2017 Tim Carter

I'd use drywall that is at least one-half inch thick and would seriously consider using 5/8 inch drywall on walls and ceilings where I want sound transmission to be minimal. Thicker drywall helps soundproof rooms.

9-Foot Ceilings

There's another distinct advantage to using one-half or 5/8 inch drywall. Both of these sizes are commonly available in stretch boards that are 54 inches wide instead of the normal 48 inch width.

These wider sheets will allow you to install the drywall horizontally since your ceiling is higher than 8 feet. Using the wider sized drywall allows you to have one continuous tapered seam all the way around the room.

There will be no need for the small troublesome ripper strip that would have been only 7 or 8 inches wide near the floor or ceiling.

Hang drywall the correct way. Learn the secrets to great drywall installation in this Drywall / Plaster Installation Checklist. I offer a 100% Money Back Guarantee.

Extension Jamb Hassle

Once the drywall is installed, you will need to add small pieces of finish lumber at all window and door jambs. White pine, poplar or other fine-grained lumber can be used with great success to make these small extension jambs.

Drywall Over Paneling

Check out how great this painted paneling looks! The entire room was painted in half a day. It would take days to add drywall and make all of the necessary carpentry changes for the drywall to work. PHOTO BY: Kathleen Connick with Tim Carter's camera

Try to make sure the added lumber sticks about 1/32nd of an inch past the finished surface of the drywall. This very slight offset will help you as you start to reinstall the exiting or new woodwork around each window and door.

Electric Box Code

You also need to be very observant around all electrical boxes. The electrical code is very specific about the distance between the edge of electrical boxes and the finished wall surface. The safest approach is to have the front edge of the electrical box flush with the finished surface of the wall.

But the code understands this can be tough to achieve and typically the maximum distance the box edge can be away from the finished wall is only 1/4 inch. But check with your local code authorities for the exact distance.

Extension Rings

If you plan to exceed this distance, you must either move the boxes so they comply with the code or you must add code-compliant extension rings. This is a very small detail, but an extremely important one.

Door Swing Issues

The extension jambs can cause small headaches around doors that pivot on traditional hinges. When a standard swing door is hung properly, the hinge is set so the door can swing back on itself and open a full 180 degrees.

But if you start to bring the finished wall surface out from the pivot point, the door starts to hit the wall before it opens 180 degrees. Usually you have to have the wall sticking out from the pivot point more than one-half inch for this to be a big problem.

Do The Test

As for painting paneling, you would be shocked how well it can look. A close friend of mine did this in her study and the look was stunning. The paneling in this room actually had a hand-hewn texture in addition to the vertical lines. Once the flat paint was applied to the paneling, the wall surface look much better than adjacent rooms that had smooth plaster. I was amazed at how nice the painted paneling looked.

CLICK HERE to get FREE & FAST BIDS from local painters that can do the quick painting test on your paneling.

Column 542

Septic Tank Garbage Disposal

Posted on by Tim Carter
garbage disposal for septic systems.

This is a special garbage disposal for septic systems. See that container at the bottom? A small amount of that liquid is injected into the disposal each time it turns on. This helps the waste decompose in the septic tank. CLICK THE IMAGE NOW TO BUY ONE OF THESE GREAT DISPOSALS.

Septic Tank Garbage Disposal TIPS

How Many Homes Have Septic Tanks?

How many homes in the United States do you think rely on a septic system for their household sanitation needs? Five million you guess? Go higher. Fifteen million, maybe? Still higher.

Try twenty-seven million homes. If there are an average of 3 people in each house, that's nearly 81 million people!

How Many Septic-Tank Houses Have Disposals?

Past studies indicate that of these twenty-seven-million homes, only twenty-two percent have elected to install a garbage disposal.

The seventy-eight percent who do not have garbage disposals choose not to do it largely because they feel these devices will harm their septic tanks or drain fields.

CLICK HERE to get FREE & FAST BIDS from local plumbers that can install a septic garbage disposal for you.

What are Septic Garbage Disposals?

There are special garbage disposals that are made for homes with septic systems. These come with a small container of enzymes that are injected into the mush to help break them down in the septic tank. CLICK HERE to buy one now.

Do Garbage Disposals Hurt Septic Systems?

The truth of the matter, as stated by the Federal Housing Authority and other key industry groups such as the Small Flows Clearing House, is garbage disposals don't harm a septic system. You just have to make sure the  system has been sized correctly and is maintained on a regular basis.

What Happens When the Disposal Grinds Food?

When you send solid particles into a 1,500-gallon septic tank, they can begin to accumulate. This only happens if they don't break down within the tank.

Some things can't break down. You may wash sand, clay and silt, and/or other solid non-organic things down into the tank. Small army men are also in this group.

This accumulation is called sludge. Some organic waste particles that can be broken down by the bacteria within a septic tank can sometimes become sludge if the bacteria doesn't have a chance to attack it.

CLICK HERE to get FREE & FAST BIDS from local plumbers that can install a septic garbage disposal for you.

Do Food Particles Break Down in a Septic Tank? 

The organic food particles must remain in suspension for a long enough period of time for the bacteria to eat them.

If the particles are too big or don't float, the bacteria that break down waste simply doesn't have enough time to "eat" the waste. As sludge begins to build in a septic tank, it effectively reduces the capacity of the tank and beneficial bacteria.

How Much Sludge Can Be in a Septic Tank?

In our case, let's say that 400 gallons of sludge is in the bottom of the tank. This means we only have 1,100 gallons of bacteria filled water left to attack food and other waste particles. This is one reason septic tanks need to be pumped out at least every three years.

You need to get rid of the sludge.

Is it starting to become clear why regular tank maintenance is important? For the same reason, you should avoid sending solid objects such as cat litter, plastic Star Wars figures, and other objects towards the septic tank.

Are There Good Septic Tank Additives?

You can purchase countless good septic tank and system additives. The Small Flows Clearinghouse in West Virginia did a study on these years ago. At the time, they couldn't determine if the popular additives really did any good. You adding them to your septic tank may be just making you feel better, not necessarily your tank.

septic tank treatment additive green gobbler

Here's one septic tank treatment product. CLICK or TAP HERE to see others.

Should Oxygen Be Added to a Septic System?

Oxygen Bleach

Stain Solver can inject lots of oxygen into your septic tank. It's MADE in the USA with USA ingredients that are food-grade quality. CLICK THE IMAGE to order some NOW.

You can add oxygen bleach to your septic system. Oxygen is what the big municipal sewage-treatment plants use to break down sewage. The second stage of sewage treatment is called aeration.

You can add Stain Solver oxygen bleach to your septic system once a week to give it a boost of oxygen. Just pour in 1/4 cup of Stain Solver into your toilet and flush it twice to get the powder down into the septic tank.

Stain Solver is Made in the USA with USA ingredients. It's certified organic so it's SAFE for your septic system.

When you add it, trillions of oxygen bubbles invigorate the beneficial bacteria in the septic tank.

Can Some Additives Hurt a Septic Tank?

Yes, some additives might be harmful to the biological activity within the septic system. In fact, some additives can rapidly kill the bacteria within the tank. Any product that contains chlorine bleach is bad for your septic tank and septic system.

The chemical name for chlorine bleach is sodium hypochlorite. Look for this fancy name on the labels of products.

If this happens you will quickly ruin your entire system as solid particles of waste will be carried to the drain field. When this happens, it is curtains.

The solid particles clog the gravel and soil that surrounds the perforated drain pipe in the leach field. Clogged gravel and soil means the polluted water has nowhere to go but the surface or it can travel through the soil to contaminate other groundwater resources.

 

CLICK HERE to get FREE & FAST BIDS from local plumbers that can install a septic garbage disposal for you.

Related Articles:   Septic Tank Maintenance,  Garbage Disposal for Septic Tank Manufacturer,  Safe Septic Tank Additives,  Disposals Harm Septic Systems - Garbage!

Column B225

Efflorescence Removal

Posted on by Tim Carter

Efflorescence Removal TIPS

Removing Efflorescence

Efflorescence removal is not easy. The first step is to simply brush the salt deposits off the surface with a stiff broom. Vacuum salt deposits or brush them away are the the best methods of efflorescence removal.

It's important to realize the next rainfall will allow the salts to re-enter the brick or concrete if you don't get rid of the salt deposits or just allow them to lay on the surface . The problem then starts all over again when the water evaporates bringing the salts back to the surface.

efflorescence

This is efflorescence on new basement floor tile. The water infiltration needs to be stopped first. Copyright 2017 Tim Carter

Do NOT Use Water

Another key point is the use of water is not recommended. The water will dissolve some of the salts and actually drive them back into the masonry. These salts will subsequently re-appear when this secondary water evaporates.

Acid Wash Efflorescence Removal

It's important to realize that dilute solutions of muriatic acid can be used. However, BEWARE of this method.

Muriatic acid

Muriatic acid is powerful and needs to be treated with lots of respect. CLICK THE IMAGE TO ORDER SOME NOW.

Muriatic acid can cause serious eye and skin burns. The vapors are also very toxic. Muriatic acid, improperly applied to a masonry surface, can 'burn' the brick and cause discoloration.

Always dilute the muriatic acid with water. Try a solution of ten parts water to one part acid.

IMPORTANT TIP: This method of cleaning is only recommended for heavy flow deposits of salts that resemble stalagmites and stalactites in a cave.

Sealing Brick

Brick that is still experiencing efflorescence should not be sealed. If you do this, there is a possibility that you can actually damage the surface of the brick.

mortar fungus

Efflorescence growing in the mortar of a brick fireplace. Photo Credit: Michael Hannum

The sealer can actually block the movement of salts to the surface of the brick. Now, you may think that is not such a bad idea. Well, here is what can happen.

Spalling Danger

The salts work their way to the sealer at the surface of the brick and stop. The concentration of the salts increases as the water evaporates. In certain instances, the salts begin to crystallize.

This process of crystallization can create enormous pressure on a microscopic level that can actually cause the face of the brick to pop off or spall.

Over the years, I've seen many different spellings of efflorescence. Here's my growing list: effervesce, effervescence, effervescent, effleresants, effloreflance, efflorescence, efflorressance, effluorescence, eflorescence, eflorescents, ellforesce and ifflorescence.

CLICK HERE to get FREE & FAST BIDS from local masonry experts who can help clean or repair your brick and stonework.

Column B033

Cultured Marble

Posted on by Tim Carter

Cultured Marble TIPS

DEAR TIM: I'm really fed up with the constant care that my ceramic tile bathtub and shower surround requires. I'd love to have a single piece of marble on each wall.

I've not won the lottery, do you think the cultured marble products will suffice?

Will these synthetic products loose their shine over time? Is it possible for the average person to install cultured marble products? Can you repair pieces that are damaged? Mack T., Liberty, IN

DEAR MACK: Let's set the record straight before we go any further. Cultured marble is really not a totally synthetic product.

Real Marble Dust is Used

Real natural marble dust is used to make cultured marble. This ground-up marble dust accounts for over 75 percent of the volume of a typical cultured marble product.

The marble dust and liquid polyester resin form an attractive and durable bathroom and kitchen product.

I can attest to how cultured marble has rock in it because the sink and countertops made from it are quite heavy!


CLICK HERE to get FREE & FAST BIDS from local contractors who can clean and restore synthetic marble.

cultured marble

It's tough to see the veining in these giant solid sheets of synthetic marble. No grout lines make it easy to clean. Copyright 2017 Tim Carter

Marble Issues

It's important to realize, real marble can be a nightmare in a bathroom or kitchen environment. It's naturally porous and as such can stain easily. Hair coloring products, chemically reactive shampoos and conditioners, and many colored liquids can cause staining problems with natural marble.

Stain Resistant

High-quality cultured marble can withstand stains that might otherwise harm natural marble. The resin in the composite marble gives it this quality. This synthetic marble can stain so you don't want to be careless with any personal-care liquid or food item that's acidic.

History Of Cultured Marble

Another key point is the cultured marble industry is now quite mature and very interesting. It got its start in the late 1960's as a "garage" business. Small volume local fabricators sold their products to plumbing and building supply houses.

The industry continues to be quite fragmented and there are hundreds, if not thousands, of small companies who produce cultured marble all over the United States.

Quality Control

For this reason the quality of the finished product can vary widely from one manufacturer to another. Since the marble dust and polyester resin are mixed at the small factories, there can be errors or a fabricator may decide to use less of the most expensive ingredient to lower his costs.

Pro Association

Years ago, many of the leaders in the industry founded the International Cast Polymer Association. This group, at one time, had a certification process so consumers could tell what members made great products.

Certified members of the association are committed to making a high-quality cultured marble, granite, onyx and solid surface product. Cultured marble made by a certified manufacturer, should maintain its brilliance for many, many years as long as you care for it.

Many Products

Cultured marble can be used to create many bathroom and kitchen products. Sinks with integral tops, bathtubs, whirlpool baths, shower basins, back splashes, wall panels, etc. are all possible.

Since it's a molded product, manufacturers can create an infinite amount of designs tinted to any color. The clear finish can be ordered high gloss or satin from many manufacturers.

CLICK HERE to get FREE & FAST BIDS from local contractors who can clean and restore your synthetic marble.

Restoring Gloss

Cultured marble that has lost its shine can be restored by using Gel-Gloss or Counter Top Magic once a year. 

cultured-marble-polish

Here's a great polish for dull cultured marble. CLICK THE IMAGE NOW TO ORDER IT.

Repairing Scratches

It's possible to repair scratches, chips, and minor blemishes. A certified repair person can re-buff the surface with a special mixed gel-coat compound.

You can also use a DIY repair kit that can often make scratches or chips disappear.

cultured-marble-repair

This kit is Made in the USA and it says it's for marble. Any kit that says it will work on marble WILL WORK on cultured marble. If in doubt, contact the Cast Polymer Association for their best recommendation. CLICK THE IMAGE TO BUY THIS KIT NOW.

Cracks and broken pieces are virtually impossible to repair. It's not possible to apply a complete new clear finish to a cultured marble product once it's left the factory.

Install Tips

Installation of cultured marble tub and shower surrounds is really simple. The process goes quickly if the wall surfaces are plumb, square, and flat.

The walls behind the cultured marble should be flat white. Colored drywall or gray cement board can show through some light-colored marble products.

Dry Fit First

With this in mind dry fit each piece to make sure they are sized correctly. Remove dust from the back of each piece with rubbing alcohol before you apply clear 100-percent clear silicone caulk adhesive.

Three-Piece Tub & Showers

I prefer to start my installations with the piece that goes on the wall I face as I enter the tub or shower. If you install the side wall pieces first, your cuts on the final piece have to be perfect.

That can be tough for a beginner. Caulk all seams with a colored 100-percent silicone caulk that will closely match the cultured marble.

No Abrasive Cleaners

Cultured marble is easy to care for once installed. Avoid any cleaning product that contains abrasives. Use a squeegee after each shower to quickly remove water drops from walls.

Hard water deposits can be dissolved easily with white vinegar applied from a spray bottle. Apply the vinegar and wait for 45 minutes to an hour.

Rinse the softened deposits with clear water and a sponge or cleaning rag. Heavy hard-water deposits may require multiple vinegar spray applications.

CLICK HERE to get FREE & FAST BIDS from local contractors who can clean and restore synthetic marble.

 

Column 218

How to Paint Aluminum Gutters

Posted on by Tim Carter
paint aluminum gutters

Paint aluminum gutters | Here are a typical aluminum gutter and downspout. The front of the gutter is filthy and covered with diesel-fuel soot from tens of thousands of trucks that traverse the interstate highways just a few miles away. Zebra stripping you see on the face of gutters is often from diesel soot that sits on the small flat ledge on top of the gutter and then runs down with each rain. Stain Solver oxygen bleach will CLEAN the zebra stripes. CLICK THIS IMAGE NOW to ORDER Stain Solver magic oxygen bleach. (C) Copyright 2017 Tim Carter

"The key to repainting aluminum gutters and downspouts is making sure they're clean and that you use the right primer if you use a common paint that contains ammonia."

Paint Aluminum Gutters Checklist

DEAR TIM: Many years ago, I had white aluminum gutters and downspouts installed on my home. They're in great shape except for the faded paint finish.

I want to paint aluminum gutters now! Can I paint the aluminum surfaces and if so, what is the best way? I'm thinking of pressure washing the entire exterior surface of my home before painting. Is this a good idea? Leslie M., Linden, NJ

Related Links:

Aluminum Siding Painting Tips

Paint Your Aluminum Siding

Aluminum Siding - Paint and Primer Tips

DEAR LESLIE: I've got good news and bad news. Let's start with the good news first.

You can paint aluminum gutters. It's not hard to do, but if you make a mistake, the next time it rains they'll look like a blistered hot dog sweltering on a grill at a Fourth-of-July picnic.

Does Paint Stick Well to Metal?

Much to the surprise of many people, metal surfaces actually are very compatible with paint. Just look around you at all of the painted automobiles, appliances, and commercial steel buildings and metal roofs.

Aluminum is especially paint-friendly as you've witnessed on your own home. Since it doesn't rust, blistering or peeling of factory-applied paint finishes on aluminum is very rare.

What Is the First Step in Painting Aluminum?

The key to repainting aluminum gutters and downspouts is making sure they're clean and that you use the right primer if you use a common paint that contains ammonia.

Does Pressure Washing Get Rid of All Dirt?

Pressure washing the gutters and downspouts and the rest of your exterior surfaces is simply not the best way to get them ready to paint. This method doesn't get rid of all the dirt.

The proof is available in two forms. When you shower each day, I'd venture to say that you don't just rotate in circles in the shower allowing a vigorous stream of water to do all the work. Even if soapy water came out of the shower head and you let that water hit your skin, you'd not be completely clean.

You most likely rub your skin using your hands with soap and water and then rinse with the water stream. The mechanical movement of your hands on your skin is what gets you clean. The soap helps lift oils and dirt from your skin as well to get you even cleaner.

Do Car Washes Get Cars Really Clean?

Do you want more proof? Take your car to a self-clean car wash equipped with a pressure washing wand. Clean your car allowing the tip of the pressure washer to get as close to your car as you feel comfortable.

After leaving the car wash, pull out into the parking lot and allow your car air dry. Take your fingers and wipe them across the paint. I guarantee you that you'll remove a thin layer of dirt that was left behind by the pressure washer.

What is Stain Solver?

Oxygen Bleach

Stain Solver is MADE in the USA with USA ingredients that are food-grade quality. CLICK THE IMAGE to order some NOW.

I'd use Stain Solver certified organic oxygen bleach to wash the gutters, downspouts and entire house to get it clean

Stain Solver is a pure powder you mix with warm tap water. Stir until dissolved and put the solution in a garden hand-pump sprayer.

Stain Solver is Made in the USA with USA ingredients.

Spray the surfaces you want to clean and allow the oxygen-bleach solution to bubble and fizz. Work in the shade or early morning if you can. You don't want the solution to evaporate.

You want the Stain Solver solution to soak and work on the surfaces for about 15 minutes before you continue to wash. Don't allow the solution to evaporate.

How Should I Clean the Aluminum Gutters?

Continue to wash your house and the gutters and downspouts as you would your own body.

I think the best thing to use is a great brush on a pole like RV owners use.

RV Brush

This is a great RV brush that's got an adjustable handle. It's perfect for cleaning siding. CLICK THE IMAGE NOW TO ORDER ONE.

These brushes are stiff enough to get rid of dirt and algae, but soft enough not to scratch window glass, paint or siding.

Should I Use Liquid Dish Soap?

Mix some liquid dish soap in the garden sprayer along with the Stain Solver solution. I prefer to use liquid dishwashing soaps as they make lots of suds. Spray this solution onto all the surfaces just before using the RV brush. Keep the RV brush wet with the soapy solution.

Rinse the surfaces as soon as you stop scrubbing. Don't allow the dirty solution to dry on the surfaces.

Be sure to scrape any loose paint before you wash. If you have wood on your home, you'll probably need to scrape a second time after washing. Paint adjacent to bare spots of wood always seems to pull away once the rinse water dries.

What About Chalky Paint?

After the gutters and downspouts are dry, they still may be chalky. This is normal. The chalk is simply pigment particles at the surface of the original paint that has been loosened by the harsh ultraviolet (UV) rays of the sun.

Are the Paint & Primer In One a Good Product?

Modern paints often say they're a paint and primer in one. That may be well and good, but you need to look on the label to ensure it doesn't contain ammonia, a common household chemical.

If you want a great spray paint that's SAFE to use on aluminum gutters and downspouts, then consider X-0 Rust. This is a fantastic oil-based spray paint that will bond well with clean aluminum. It comes in different colors, including white.

X-O Rust Paint and Primer spray can

Here's a spray paint that's great for steel beams and columns. It contains a metal primer. This brand also is available in quart or gallon cans if you have LOTS of steel to paint. CLICK THE IMAGE TO ORDER IT NOW.

Is Ammonia in Paint a Problem?

You've now reached the most important part of the job - the primer.

IMPORTANT TIP: Avoid using any latex paint primer that contains ammonia. This ingredient is often listed on the paint can label or a technical sheet that the paint store has on file.

Ammonia can react with oxidized aluminum that is hiding inside small pin holes or bare spots on your gutters and down spouts. When this happens, the chemical reaction creates a gas bubble just beneath the skinned over latex paint.

What Causes Bubbles in the Paint?

The next time the air pressure drops in advance of rain storm or shower, the bubbles actually inflate! When the pressure rises as the weather clears, the bubbles mysteriously disappear. Keep in mind the paint film is a latex film much like a balloon or gloves a forensic scientist wears.

Are Special Primers a Good Idea?

There are two primers that work great for faded aluminum. Get the clear acrylic bonding primer shown below that penetrates the chalky aluminum. This product forms an excellent foundation for a final coat of 100 percent acrylic paint.

Clear Bonding Primer

This is a great clear bonding primer. CLICK THE IMAGE NOW TO ORDER IT.

It'll say on the label that's it's approved for use with aluminum.

If you can't locate this nifty clear primer, then use a regular oil-based metal primer. The trick is to thin the primer with 16 ounces of thinner per gallon of paint.

Feel free to add some pigment to this primer if you feel it will get you close to the final color of your trim.

Try to apply the final coat of paint within 24 hours of applying the primer. The top coat paint will bond much better if you can do this.

Companion Articles:  Aluminum Siding Painting Tips, Paint Your Aluminum Siding, Aluminum Siding Paint Manufacturers, Aluminum Siding - Paint and Primer Tips

Column 274

Ceramic Tile Wall Gap Issue

Posted on by Tim Carter
ceramic tile wall gap

This is a horrible mess. Don't ever accept poor workmanship like this. (C) Copyright 2017 Tim Carter

Ceramic Tile Wall Gap TIPS

DEAR TIM: I’m having a small bathroom remodeled. My wife and I thought we did our due diligence and hired a great contractor. I came home from work to discover the ceramic will tile has a gap issue.

The back of the decorative edge tile is floating above the adjacent wall by almost one-half inch. The remodeling contractor tells me the tile setter is going to fill the gap to make it go away. Is this normal? I’ve never seen the tile sit higher than the adjacent walls.

What could we have done to prevent the issue and should the tile be torn out and redone? Chris C., Washington, DC

DEAR CHRIS: Oh my goodness! The photo you sent made my eyes cringe. That’s got to be the worst ceramic wall tile mistake I’ve ever seen.

Shame on the contractor for trying to cover up for his tile setter’s poor workmanship. The buck stops with the remodeling contractor and he should have known about this issue before it became one.

Before I address what you could have done, let’s talk about what the tile setter should have done and the options available to you now at this point. When I see mistakes like this, I often wonder how many homeowners back down and allow the work to remain in place.

CLICK HERE to get FREE & FAST BIDS from local tile contractors who'll do a great job. Just show them photos.

Keep Eyes Open

You did a magnificent job over the years looking at other ceramic tile installations and filing away in your head what looked good to you, or at the very least, what was the baseline norm.

Flush Finishes

As you said, you’ve never seen tile sit so high off a wall. That’s because professional tile setters know to make sure that the base they put their tile on is flush with the adjacent finished wall surface.

Tile Setter Innocent?

I know this sounds crazy, but the tile setter may not have made the mistake. It’s very unlikely, but perhaps the wrong thickness of finished wall material was installed after the tile backer board was already up. I’d say the odds of this are very small, but it’s a possibility.

Contractor In Charge

In any event, the buck stops with the remodeling contractor. It’s his job to make sure all aspects of the job are progressing and all the correct materials are on the job so the final product is perfect, or nearly so.

Common Thickness

Most builders and remodelers use one-half-inch drywall on the walls in bathrooms. The manufacturers of the tile backer boards, both the cement board and the waterproof gypsum-core backer board, make their products the same thickness so the back side of the tile sits just about one-sixteenth or one-eighth-inch above the surface of the drywall after the tile’s installed.

This smaller gap is created by the compressed thickness of the organic mastic or the cement thinset the tile setter uses to attach the tile to the backer board. The gap is easily filled with the tile wall grout and it looks great once complete.

CLICK HERE to get FREE & FAST BIDS from local tile contractors who'll do a great job. Just show them photos.

Straight Walls

It’s also important for the rough carpenter to get the wall framing perfect so all this works out. The wall studs can’t have horrible crowns or be out of plumb. A crown is a hump in a wall stud that creates a bulge in the wall. If the crown points the other way, t creates a depression in the wall. Both are bad when you’re installing large pieces of ceramic tile.

Steel Studs

Great remodelers and builders consider using galvanized steel studs in locations where there will be tile. The steel studs are perfectly straight. If installed plumb and square, the finished tile work looks amazing.

The other advantage to using steel studs in these areas is they don’t warp or shrink. Modern lumber has been hybridized by the lumber companies so it grows faster in the forest. The downside to this is the light-colored spring wood bands are huge and the lumber is much less stable than lumber from even forty years ago.

Fixing The Problem

Here are a few options you have at this point. You can remove the tile and start over, but this is going to be very painful. I’m not at your home and don’t know if this is possible, but the contractor may be able to install an additional layer of drywall on the existing drywall to correct the error.

Drywall comes in different thicknesses including 1/4-inch, 3/8-inch, 1/2-inch and 5/8-inch. One of these sizes may work perfectly and the drywall might slide under the overhanging edge of the tile.

Tile Tools

What tools do you need to complete a simple tile job? Here's a list:

  • tape measure
  • pencil
  • tile cutter
  • nippers
  • a 1/4 by 1/4 inch v-notched trowel
  • a hammer
  • some 6d finish nails
  • 8 lineal feet of straight 1/4 inch wood lattice strip
  • putty knife
  • 3-inch wide-bladed scraper
  • grout sponge
  • rubber grout float
  • several buckets
  • accurate 4 foot level

Click the image below to BUY all, or some, of the tools in the above list.

ceramic tile tools list

CLICK THIS IMAGE NOW TO ORDER ALL THE TOOLS YOU NEED TO DO CERAMIC TILE.

Preventing the Problem

While this is lots of work, here’s how you might have prevented the error. You could have downloaded from the Internet lots of detailed photos of exactly how you expected everything to look once the job was complete.

Or, you may have taken lots of great photos from model homes you may have visited over the years. I’m talking about close-up photos of great details of tile work, door trim miter joints, baseboard details where it meets flooring, kitchen backsplashes, etc.

Photos In Bids & Contract

These photos should have been part of the bid package plans and specifications so each contractor knows the level of quality they must achieve. They should also have been part of your written contract so you can use them to withhold payments until the work meets your expectations. Few will take the time to do this, but it pays huge dividends to those homeowners that refuse to *hope* everything works out.

CLICK HERE to get FREE & FAST BIDS from local tile contractors who'll do a great job. Just show them photos.

Column 1182

February 5, 2017 AsktheBuilder Newsletter

Posted on by Tim Carter

If you're a new, or newer, subscriber, then you've got no idea about what's going to happen this issue.

Every now and then I share an amazing new product with you in a fun and challenging way.

Today's one of those days.

I'm VERY EXCITED about this new product because it's a game changer.

It's also a product you can use on something you've previously purchased so that means everyone gets to benefit!

Win Win Win indeed just like one team's going to tonight!

Tell Me More Tim!

This is so easy and it's just a few steps.

Step One is to click all the following links and study the photos closely. You can CLICK the photos once there to see a LARGER ONE. Some have multiple views! Each one is different.

Mystical Blue Glow & The Red Diamond

Hidden Art Gallery & Trilobite Vase

The Great White Whale

African Safari and Telephone Pole Indoors

Two Giant Ghost Eyeballs & Hidden Red Face

Step Two is to CLICK HERE and answer my questions.

You can try to guess how much coffee I had creating the multiple-choice answers. BWAHAHAHAHAHAAHA!

LE Johnson NEW Soft-Close Door Hardware

If you took the time above to check out all the eye-popping photos, you're in luck.

Each of the doors, and any others you can DREAM OF, can be equipped with the new LE Johnson Soft-Close kit.

CLICK HERE to see it.

What's so great about this NEW hardware that's hidden up above the doors?

  • Prevents door SLAMMING
  • Reduces NOISE for those sleeping
  • Prevents pinched fingers - Yeeeeeouch!
  • Reduces wear on painted or stained doors & jambs
  • Installs in less than an hour

You can put this great hardware on these LE JOHNSON pocket, sliding or wall-mounted doors kits:

  • 138F
  • 134F
  • 100PD
  • 100SD
  • 2610F
  • 1500
  • 1562
  • 2710

CLICK HERE again to see this very cool soft-close hardware. Oh, and here's the best part:

LE Johnson Soft-Close hardware, as well as all the other stuff they make, is Made in the USA.

Good ole Indiana!

That's quite enough for today!

Please realize you clicking the above links makes it possible for me to continue to provide this FREE newsletter to you.

Without the support of fantastic companies like LE Johnson, I'd not be able to spend the time to create this content each week for you.

Tim Carter
Founder - www.AsktheBuilder.com

Do It Right, Not Over!

The Existing Home Inspection

Posted on by Tim Carter
Home inspection

I don't know about you, but I can clearly see a patched crack in this brickwork. Structural defects are very hard to disguise, but rest assured people try to do it all of the time.

Existing Home Inspection TIPS

DEAR TIM: My husband and I are getting ready to purchase an existing home. We don't want to buy one with lots of defects. Can we inspect the house ourselves or is it necessary to have the house inspected by a professional?

If so, how do you locate a good house inspector? What types of things should we be looking for as we walk through the house? Sally M., Bedford, IN

DEAR SALLY: Many years ago I used to do home inspections for buyers before there were inspectors. The buyers I worked with felt that a seasoned builder knew what to look for in a house, and how to spot small problems before they become big problems.

Ever since the early 1980s, the home inspection industry has become a big business. Just about every home buyer in my town requests an inspection from a full-time home inspector. Not only is it a good idea for existing homes, but home inspections are also a swell idea for new homes too.

Trained Eyes

I doubt that you can do a thorough home inspection. A knowledgeable home inspector takes years to train. The best inspectors have lots of field experience, have passed written examinations, are fully insured and take ongoing continuing education.

CLICK HERE to get FREE & FAST BIDS from local home inspectors.

Bogus Inspectors

There are several national associations out there that home inspectors belong to. Some are legitimate and others just sell worthless certificates.

You want to deal with a home inspector that's been trained and is knowledgeable about both patent and latent house defects.

When you've forged the initial contract with a seller, be sure to use the absolute best inspector you can find. Ask the inspector to provide you with a certificate of insurance that indicates he/she has professional liability or errors and omissions coverage. Be sure that the policy is current and that there is enough coverage to pay for a mistake(s).

Inspections Save $$$

An expert home inspection can save you hundreds if not thousands of dollars. A competent inspector will spot problems that may cause you to rethink your purchasing decision.

Walk, No Run, Away

Sometimes it is better to walk away from a problem house rather than try to spend years of hard earned dollars fixing problems. Buyers are often blinded by dreams that obscure blatant defects and flaws.

Professional inspectors have no emotional ties to the transaction and are there to find flaws. Don't ever purchase a home that's got a visible structural defect. It's almost impossible to hide them and a future buyer will penalize you and try to get you to lower your price.

DIY Initial Inspection

Hiring a professional inspector costs hundreds of dollars. Back in 2008 when I purchased an existing home in New Hampshire I paid an ASHI inspector, they're the best around, $495 to look over the house to make sure I didn't miss anything.

Imagine if the inspection showed up a defect and I backed out of the deal? Yes, I would have saved money, but it cost me $495 to find that out. In today's market that inspection fee has to be much more.

I knew what to look for. Do you? My guess is you'd overlook about ten, or more, things that would be giant flashing red lights.

I developed a very cool checklist. You use it to spot obvious bad flaws in a home BEFORE you call in the expensive inspector. Why spend more than $500 when you can identify flaws for $17?

My checklist helps you locate obvious defects as you walk through a house for the first time. If you discover enough problems, you may choose not to make an initial offer on a particular piece of property.

CLICK HERE NOW to get my DIY Home Inspection checklist. It will allow you to SPOT a lemon before you make an offer!

Structural Problems

I suggest you begin by looking for obvious structural problems. These can be cracked foundations, slanted floors, bowed or bent beams, doors and windows that don't fit uniformly within a frame, cracks in brickwork and stucco, severely cracked concrete floors and slabs, etc.

CLICK HERE to get FREE & FAST BIDS from local home inspectors.

Expensive Repairs

Structural problems tend to be the most expensive problems to repair. Houses with structural problems can also be harder to sell in the future. The repairs often leave scars. (See photo at top of this column.) A future buyer will see a repair attempt and possibly wonder if the problem has really been rectified. You may suffer financially if this happens.

Water Nightmares

Moisture problems are sometimes easy to spot. Look for stained ceilings, walls, interior foundations, basement floors, exterior siding, damp crawlspaces and moisture around plumbing water and drain lines.

Hunt for efflorescence salts.

These fluffy gray-white powdery deposits can be found along cracks in basement floors and walls and in masonry work. They are usually a sure sign of water infiltration or slow seepage.

Flooded Basements & Firemen

Consider a visit to the closest firehouse. If the fire department has made visits to pump water out of the house for any reason, it should show in the public record of their run activity.

Great Drainage

Inspect the exterior for drainage problems. I prefer to see a minimum of four to six inches of foundation projecting above the soil around the entire house.

Soil should slope at least 6 inches within the first ten feet of run away from the foundation. Look for raised planting beds that can trap water against a house.

Beware Realtor Trick

I was a licensed real estate broker in Ohio for nearly twenty years. Believe me when I say there were unethical salespeople and brokers in the marketplace.

The unethical professionals would steer you to a substandard inspector so the deal doesn't go south. Be VERY CAREFUL about using the inspector the realtor recommends. See below.

Best Home Inspectors

When you finally decide to hire an inspector, beware of slick sales pitches and testimonials. Some associations require that an inspector simply send in an application and a small fee to become certified. You want an inspector that belongs to an association that requires experience, written examinations and continuing education. Don't settle for less!

IMPORTANT INSPECTION TIP:

At the time this column was written, the American Society of Home Inspectors (ASHI) had the toughest set of requirements for membership of all of the inspection associations. Many professional engineers who do home inspections are ASHI members.

EXTRA NEWS from Tim Carter:
Purchase my Easy-to-Use Home Inspection Checklist Now. This Simple-To-Use Tool allows you to spot many defects before you have to hire a real inspector. You can then eliminate a house and move on to one with fewer defects.

You have nothing to lose. If my checklist doesn't work for you, I'll give you your money back. Oh, one more thing, it's an Instant Download! You can have the checklist in your hands just minutes from now!

CLICK HERE to get FREE & FAST BIDS from local home inspectors.

Related Articles:  Home Inspectors & Buying New Homes,  Home Inspection Checklist,  Home Inspector Certification Associations

Column 248

Toilet Bowl Cleaner

Posted on by Tim Carter
Toilet Bowl Cleaner

The normal toilet bowl cleaners you get at the grocery often don’t have the power to really clean a toilet. You may need to use muriatic acid. ©2017 Tim Carter

Toilet Bowl Cleaner TIPS

DEAR TIM: I’m at my wits end with toilet bowl cleaners. My toilet has light and dark stains in the bottom of the bowl as well as up under the rim.

I’ve tried all of the national-brand the store-bought toilet bowl cleaners and even the automatic toilet bowl cleaners that fit on the rim of the bowl and stick to the bowl.

None of them do anything to cut the stains. What’s causing the stains and what, if anything, can I do to get my toilet looking respectable. It’s embarrassing and I’m about ready to rip it out and purchase a new toilet. Help me please. Amy H., Lexington, KY

This popular column was shared with all my readers in the April 3, 2015 AsktheBuilder Weekend Warrior.

DEAR AMY: Oh, I’ve been where you’re at. I remember years ago suffering trying to get a cleaner toilet bowl using all the different products at the grocery store as well as every type of brush and scrubbing pad known to man and woman.

I have clear memories of wearing rubber gloves and goggles trying to restore a deeply stained toilet in the basement of a past house I owned. Believe me, it didn't take long to get frustrated like you.

CLICK HERE to get FREE & FAST BIDS from local cleaning companies that will follow the advice below to get your toilet CLEAN.

Tear-Pants Limestone

I got my toilets sparkling clean, but only after I stepped back and thought about some of the things I had discovered in my college chemistry and geology-lab classes.

Decades ago I was a geology student attending a six-week field course camp in the Tobacco Root Mountains of Montana. CLICK HERE to get a fantastic map of this gorgeous mountain region.

tobacco root trail guide

If you want to go hiking instead of cleaning your toilet, I don't blame you. Use this great book to wander across trails I walked while mapping rocks. CLICK THE IMAGE TO ORDER THIS RARE BOOK.

There I was introduced to the infamous tear-pants limestone. We always used a drop or two of acid I carried with me in a tiny bottle to test to see if the rock was, indeed, the sinister limestone.

If the acid reacted with the rock, it would fizz when the acid was dropped on it. When you saw this bubbling and fizzing, you knew the rock contained calcium and magnesium. There was no need to sit on the rock and tear your pants, you knew it was the evil limestone.

Tiny Rocks In Your Toilet

You’re a victim of hard water and lime buildup. It’s very common in many areas of the USA, especially those that have a high concentration of certain dissolved minerals in the water supply.

You have microscopic limestone rocks growing in your toilet and it's all your fault.

A Layer Each Flush

If you have calcium, magnesium and a few other elements in your water, these can create multilayer deposits inside a toilet. Not only can these deposits be unsightly, but they also can significantly impact the performance of the toilet.

If your toilet is like several I’ve had, my guess is that you’ve also noticed that the flushing has become sluggish or not as powerful as it once was.

Trapped Dirt and Stains

The ugly deposits happen when dirt gets trapped in between layers of hard water deposits in the toilet. This is most common under the rim of the toilet bowl and along the sides of the toilet bowl above the water line.

Each time you flush the toilet these areas of the toilet get wet. Once you leave the bathroom, the water evaporates leaving behind an ultra-thin film of minerals. Dirt can easily attach itself to this coarse layer that resembles sandpaper.

Hundreds / Thousands Of Layers

The next flush introduces another sheet of water containing the minerals. The water evaporates and now the fresh mineral buildup locks in the stain. Imagine this happening thousands of times over several years worth of flushes.

Blocked Syphon Jet

You can also get a lime layer buildup in the bottom of the toilet bowl that starts to block the syphon-jet hole. It’s very important that this hole is wide open so that the maximum amount of water can enter the toilet bowl as fast as possible to initiate the flush. Water entering through the rim of the bowl can also be slowed by mineral deposits in the small holes under the rim.

Muriatic Acid

The best toilet bowl cleaner I’ve come across in these situations is muriatic acid. CLICK HERE to have it delivered to your home.

muriatic acid

Muriatic acid is powerful and needs to be treated with lots of respect. CLICK THE IMAGE TO ORDER SOME NOW.

IMPORTANT SAFETY TIP: Muriatic acid is a very powerful chemical that should be used with great care and respect. The fumes are very nasty and the acid can easily cause skin burns and ruin fabrics that it soaks into. Before using it, read the warnings on the label.

Alakazam Acid!

When this acid contacts lime and other hard-water deposits, it rapidly dissolves them. Once the deposits have been removed, the toilet looks brand new.

Muriatic acid will clean the stains from the bowl, the deposits in the syphon-jet hole and the rinse and vortex holes under the rim of the bowl.

CLICK HERE to get FREE & FAST BIDS from local cleaning companies that will use muriatic acid. Just ask them.

Sanitize Bowl

I always start the cleaning project by using the standard toilet bowl cleaners to sanitize the bowl. Just clean the toilet as you normally would with regular cleaners.

Once this is complete, I dump five gallons of water into the bowl as fast as I can.

This rapid influx of water simulates a flush and since no water is coming from the tank it leaves a small amount of water in the bottom of the bowl.

Add the Acid

Then I slowly pour into the bowl about 12 ounces of muriatic acid. You can add more, but it's not necessary.

Safety Gear

Be sure you have the bathroom well ventilated, preferably with a window open to exhaust the acid fumes. Wear tight-fitting goggles, rubber gloves, old clothes with long sleeves, etc. so that you have virtually no skin exposed. Anything that the acid touches, including good towels, great carpeting, a throw rug, the side of the vanity cabinet, etc. will be RUINED by the solution.

Swish The Solution

Carefully use a toilet brush to spread and swish the acid solution under the rim of the bowl and on the sides of the bowl. Do this multiple times over a period of 30 minutes. Continue to apply the solution to the underside of the bowl rim every 15 minutes for up to two hours.

Children and Animals

If you have small curious children and animals, do NOT do this job alone. You need an adult helper to keep kids and animals away from you and the toilet at all times.

If you have to leave the room, always put the toilet lid down to prevent animals from accessing the acid solution. If children are in the house, never leave the toilet alone. Work until the job is finished.

Long Soak - Minimal Scrubbing

The muriatic acid will absolutely remove the hard water deposits that are trapping the stains. The longer it soaks the less you have to scrub. Never use a metal scrapper, screwdriver, etc. to dislodge any deposits. The acid will do the work for you, it just may take awhile.

No Abrasive Cleaners

Avoid using any abrasive toilet bowl cleaners. These can scratch the smooth glazed surface of the china. Take your time and slosh the acid around the bowl and twist the brush in all visible areas. Believe me, the stains and deposits will disappear in time. Depending on the thickness of the deposits, it can take hours for the acid to break them down.

Neutralize The Acid

It's best to completely neutralize the muriatic acid before you get rid of it. Some states may not permit you to flush this chemical into a public sewer system. It's also not a great idea to send acid into a septic system.

IMPORTANT TIP: This is why I instructed you to pour the bucket of water into the toilet bowl to start this process. This allows an ample amount of storage space in the toilet bowl so the acid doesn't enter the drain pipe beneath the toilet.

If you had added the muriatic acid to the normal amount of water that's always in a toiled bowl, for every ounce of liquid you put in the bowl an ounce goes down the drain pipe under the toilet. Since the acid begins to mix immediately with the water in the bowls some acid would go down the drain.

Baking Soda

To neutralize muriatic acid, you just add common baking soda. You'll need just over one-half pound of baking soda since you added just 12 ounces of muriatic acid to your toilet.

baking soda box

This is standard baking soda. Pour it in the bowl SLOWLY so the acid solution doesn't splash out! CLICK THE IMAGE NOW TO ORDER THIS BAKING SODA.

The formula is 5.5 pounds of baking soda for each concentrated gallon of muriatic acid. Keep in mind your solution is diluted because there was water already in the bottom of the toiled bowl before you added the acid.

Allow the baking soda work to neutralize the acid for about thirty minutes. Flush the toilet several times when you think your finished. Repeat the process if there are stubborn stains that didn’t come clean the first time using the industrial-strength toilet bowl cleaner.

CLICK HERE to get FREE & FAST BIDS from local cleaning companies that will use muriatic acid. Just ask them.

Column 843

Foundation Drain Tile Installation

Posted on by Tim Carter
Drain Tile

The builder is doing just about everything right installing this drain tile. The drain tile is the white pipe next to the footer. He should have 2 or 3 inches of gravel under the pipe. If the pipe has two rows of holes, they should point down in the 4 and 8-o'clock position. Finally, he should cover the drain tile with about 2 or 3 feet of gravel, not 3 inches like you see. He did put the pipe alongside the footer instead of on top and he's covered the gravel with tar paper, so it doesn't get clogged with silt from the backfill soil. Copyright 2017 Tim Carter

"The basement, before the house is built on top of it, looks just like the typical in-ground swimming pool. Once the house is built, this swimming pool gets covered."

Foundation Drain Tile Installation TIPS

Foundation drain tile systems are one of the most important aspects of residential construction if your home has a full basement or crawlspace.

Drain tile systems are also one of the most misunderstood parts of the average home - both by most uninformed builders and homeowners.

Related Links

Foundation Waterproofing Systems and Tips

Water Sitting Around Shallow Foundations

Free & Fast Bids

CLICK HERE to get FREE & FAST BIDS from local contractors who can install drainage tile.

Where Is Drain Tile Placed?

Drain tile is placed deep in the ground alongside the foundation footing.

Because these systems are usually deeply buried and cannot be easily modified or corrected, it's vitally important that they are installed correctly. Foundation drainage systems which are installed properly can serve a dual role.

Drain Tile Pipe Video

Watch this video to see the correct white PVC pipe to use and the orientation of the drain holes.

He doesn't show this pipe along a foundation but what you see are the first three steps of doing the job right.

Foundations Are Covered Swimming Pools

Many homes around the nation have full or partial basements. These basements are really reverse swimming pools.

The basement, before the house is built on top of it, looks just like the typical in-ground swimming pool. Once the house is built, this swimming pool gets covered.

But most people don't want water in their basements. Foundation drain tile systems are the means by which groundwater can be transported away from your basement. If you want a dry basement, you must have fantastic drain tile and waterproofing on the outside of the foundation.

CLICK HERE to get FREE & FAST BIDS from local foundation drainage experts.

Is There Water in Soil?

There is water in the soil. Thousands of gallons of water can be in the soil on your lot.

The water content in the soil surrounding your house can fluctuate seasonally. There's always a point at which you can dig and hit water. Geologists often refer to this as the water table.

This water table rises and falls in response to the amount of precipitation in any given time period. The water table in many parts of the country can rise to within a few feet of the surface during wet spells.

How Does Water Move Through Soil?

The water in the soil is moving all the time. In almost all cases, it moves down a few inches then it begins to move sideways. Gravity is pulling it to the oceans around the world.

drain tile

Here's a side view of a typical house. The black clouds release rain. It falls into the soil and starts to go down, but then sideways. The bedrock under the soil generally, but not always, follows the shape of the soil above it. Soil depths can vary from several feet to tens-of-feet thick. ©2017 Tim Carter

Most people think that the water in soil moves straight down but in reality, it moves sideways through the topsoil and upper layers of the B horizon of soil.

Almost all homes are built on some sort of slope, so if you have acres of land above your home, the water in the soil is all marching and flowing towards your house.

Does Water Take The Path Of Least Resistance?

Water will take the path of least resistance. It can choose to go sideways through a crack in your foundation, or it can go down alongside your foundation through clean, washed gravel into a pipe.

I'm sure that you will agree that it is a better idea for the water to go down the pipe.

How Many Parts are There to Drain Tile?

A foundation drain tile system has four main components:

  • Drain tile pipe
  • Gravel
  • Gravel Protection
  • Water outlet

All of these elements must be installed for the system to function properly.

drain tile

Here are three of the four parts of the system. The missing part is what happens with the round drain pipe. It will either extend sideways to daylight if the slope is steep around the house, or it will go under the footing to a sump pit in the basement or crawlspace. (c) 2017 Tim Carter

How Big is Drain Tile Pipe?

The drain tile or pipe is usually 4" in diameter and is perforated or has pre-drilled holes along its length. Depending upon the type, it can be purchased in rolls up to 250' or in 10-foot sections. Fittings are available to allow you to go around corners or interconnect the pipe.

I've never been a fan of the rolls of black corrugated drain tile with the slits in the cracks. I prefer the more rigid white plastic pipe with two rows of drainage holes drilled into the pipe.

CLICK HERE to get FREE & FAST BIDS from local foundation drainage experts.

How Much Gravel is Needed?

Install at least at least 2 or 3-foot thick layer of gravel over the drain tile. More is better.

The filter media or gravel is used to cover the drain tile. Water can flow readily through this gravel and find its way to the pipe.

One customer wanted me to ensure his room addition basement never had water in it. He was willing to pay to have the high-side foundation wall that pointed upslope filled completely with the nice rounded gravel.

There was no way water was going to ever try to force its way into his basement when it had the chance to go straight down to the drain-tile pipe.

Remember, water takes the path of least resistance. Some soils, heavy clays, resist water movement.

What Type and Size Gravel?

The gravel that is used most often is large 1 - 1 1/2" diameter washed rounded gravel. This gravel is about the size of a walnut or large grapes.

Some parts of the USA have crushed gravel this size. It's not rounded, but that really doesn't matter. All that matters is that you just put in this rock and no sandy gravel. Sand slows down the movement of the moving water.

If your soil is like this, the water would rather go sideways into your basement than down through the clay soil to the drain tile.

How Do You Protect the Gravel?

You must protect the gravel with a barrier. It prevents silt and mud from the soil from clogging the gravel or the drain tile pipe.

During excavation, dirt removed from the hole is fluffed. This means that it is disturbed and broken up.

It's volume usually increases about ten percent. It's loosened and disturbed more during backfilling procedures.

Does Gravity Compact the Backfill Dirt?

As the soil gets disturbed, small dirt particles, or silt, are created and separated. These are carried through the gravel by the rainwater or snowmelt which enters this soil.

Very few builders take the time to compact the soil around the outside of a house so Mother Nature does it using water and gravity.

Without a barrier of some type covering the clean gravel, these silt particles immediately clog the gravel and drain tile and render it useless.

IMPORTANT TIP: Most builders often do not install this barrier. It's a HUGE MISTAKE to eliminate it. Do NOT ALLOW them to tell you it's not needed. They're either ill-informed or lying to you.

What Material Covers the Gravel?

The materials commonly used to stop the silt from getting to the gravel are straw or tar paper.

If you use straw, just scatter a 16-inch layer on top of the gravel before you put in any soil on top of the gravel.

Tar paper is easy as you just cut the correct width and lay it on top of the gravel.

Where Does the Drain Tile Pipe End?

The water outlet is simply the place where the collected water flows to. It can be one of two places:

  • Daylight - downslope from your home
  • Sump Pit - inside a basement or crawlspace

If you build on a hillside, your drain tile will simply 'daylight' or come to the surface. This happens naturally because the drain tile pipe is installed nearly level and as the ground falls away from the house at some point the pipe will be visible.

This is the best situation because your system depends entirely on gravity to work.

Are Sump Pumps a Good Idea?

No, sump pumps are a bad idea.

If you build on level ground, you have to install a sump pit. A sump pit is usually installed inside the basement of your home.

The pit is nothing more than a buried plastic container that resembles a garbage can. It's large enough for a sump pump to rest at the bottom.

The drain tile pipe runs beneath the footer to this sump. The collected water is then mechanically pumped from the sump.

Do Sump Pumps Fail?

Yes, sump pumps stop working and the basement or crawlspace floods. They typically fail in big storms when there are extended power outages.

Sump pumps also fail because the float mechanism gets jammed or the pump burns up.

Dry Wells Don't Stay Dry

Some people say to extend the drain tile pipe to an underground dry well. A dry well is a large subterranean pit filled with gravel.

The drain tile pipe runs to this pit and the water fills this pit.

These pits work well only in places that have very open gravel soils. Not many places have this soil. In most places, the soil is dense clay and the dry well fills with water and the water then backs up against your foundation.

Should Drain Tile Be Next To the Footing?

Drain tile pipes work best when placed alongside a foundation footing, instead of on top of the footing.

By placing the pipe alongside the footing, you lower the water table below your basement floor another 6-8 inches.

When Should Drain Tile Be Installed?

In new construction, install the drain tile immediately after the footing forms are removed. Cover the pipe with gravel to a level flush with the top of the footer.

If you choose to wait until the foundation is poured, there will be less room to work in, the side walls of the excavation could cave in, or extra concrete from the foundation pour could fall into the hole and have to be removed. Believe me, it's faster and easier to install the drain tile pipe and the first layer of gravel without the foundation walls in the way.

Install Piping After Waterproofing

After the foundation walls have been waterproofed you begin step two. Backfill over the pipe with at least a three-foot-thick layer of gravel.

If you can afford it, backfill with gravel to within 18" of the finish grade. You must think long term. Remember, it will be virtually impossible to dig up and add gravel in the future when your basement is leaking. The extra money spent now is well worth it.

Once the gravel is in place, cover it with a 16-inch thick layer of straw or a single layer of 15# roofing felt paper. This barrier will prevent the silt from the backfill dirt from clogging the gravel and drain tile.

Extra Protection

To really ensure your basement or crawlspace stays dry, install a Linear French Drain around your home once it's built. I created a fantastic step-by-step Streaming Video showing you how to do this.

Linear French Drain Streaming Video

Do your own DIY install of a Linear French Drain with Tim Carter's time-tested methods and materials! CLICK IMAGE TO ORDER NOW!

CLICK HERE to get FREE & FAST BIDS from local foundation drainage experts.

Column B14