Marble Floor Repair and Cleaning

DEAR TIM: We just had marble flooring installed in our bathroom. The room has radiant heat with plastic pex plumbing stapled to the underside of the wood subfloor. I was struggling to clean the marble the other day and discovered there are cracks in the veins of the marble. I'm in tears wondering what to do. What do you think caused the cracks, how can they be repaired and is there an easier way to clean marble? Please don't tell me I have to rip out the floor and start over. Denise P., Concord, MA

DEAR DENISE: I'm sorry this has happened to you, but the good news is that there may be a very easy fix. We'll talk about that in just a bit. I'm assuming that the cracks are somewhat minor and that large chunks of marble are not coming up from the floor.

Let's talk first about the possible causes of the cracking. There are many. One or more of these could be the cause of your angst.

The seemingly harmless black tubes under the wood floor possibly contributed to the cracks in the marble flooring above. PHOTO CREDIT: Tim Carter

The seemingly harmless black tubes under the wood floor possibly contributed to the cracks in the marble flooring above. PHOTO CREDIT: Tim Carter

Your radiant heating could be the problem as it can cause expansion and contraction in the subflooring that stresses the marble. Stone usually has very high compressive strength meaning if you squeeze it, it doesn't fail. But most stones have low tensile strength - the force that happens when you pull or stretch something. Expansion of the wood floor under the marble, especially if the marble was adhered directly to the wood, could be pulling the marble apart.

The wood floor structure may also be a contributing factor. If the floor is springy and not stiff, the slight up and down movement like that of a trampoline, could be causing the same tension cracks. If there is a large tub that gets filled with water in the room, that concentrated weight can compound the problem if the wood floor joists are undersized.

The marble installer could have also made a mistake. He may not have incorporated a crack isolation membrane as part of the installation process. These membranes ensure the marble floor floats on top of the subfloor so that any sideways movement in the subfloor is not transferred to the marble flooring. This stops the tension forces from pulling apart the marble.

Finally, there could be other structural issues with the house that are manifesting themselves in the bathroom flooring. If you only see cracks in the bathroom, odds are this is not the case, but it's a remote possibility.

If your house is a new one, the issue could be also traced to lumber shrinkage. The lumber used in new homes can sometimes acquire lots of water during the construction process. As the lumber dries out, which can take sometimes over a year, this causes the wood to shrink. Shrinkage creates tension.

Now it's time for the good news. Since you have marble flooring that naturally has random veining, it's easy to disguise the repair of the cracks. I would start by doing a very small test using a wall grout that matches the color of the veining. Grout the cracks in the marble as if they were joints between tile.

It's very important the grout you use is quite stiff. Make it the consistency of premixed cake icing you'd buy at the grocery store that is about 60 F in temperature. As icing gets warmer, it becomes more fluid. You don't want that in your situation.

Use a rubber float to apply the grout and get all of the excess grout off the marble. There will be a very slight haze of grout on the marble. Don't remove this from the marble for about 30 minutes, then using only a very slightly damp sponge. You want to make sure you don't dig out any grout from the crack. The grout must be at the same height when dry as the marble floor.

I've found that oxygen bleach is a remarkable cleaner for marble. Just a week ago, I used it to remove a stubborn grease stain from marble.

Oxygen bleach is commonly sold as a powder that you mix with water. It attacks organic stains using just oxygen ions. It's color safe and should not harm the marble at all.

The trick is to mix up the solution and pour it onto the floor. You just let it soak on the marble and grout and allow the oxygen to do the work. After 15 minutes, scrub it with a stiff nylon scrub brush and rinse. The results should be remarkable.

Column 881

April 28, 2011 AsktheBuilder Tips And Newsletter

What's in This Newsletter?

Latest News
Bucket Ape Tool Review
AsktheBuilder on Facebook
Rusting Gutters
Helping You
Washington DC Meet-up
Stain Solver Sweepstakes
Latest Columns
Boring, But Necessary Stuff

 

Latest News

Spring is really trying hard to come to New Hampshire. The Friday before Easter it was 58 F and pretty sunny. That's tee shirt weather up here, especially after you've been buried under snow for three months.

Then last Saturday morning, I awake to wet snow falling. By the time it was over, two inches were on the ground. It looked like December. Easter Sunday, by 1 p.m., the ground was clear of that white covering! Crazy weather indeed.

Yesterday, we put the wood panels on the dock that lowers into the water like a drawbridge. That's how I suggest to Mother Nature, "Okay, it's time for summer!"

lake winnisquam nh

Tool Review - Bucket Ape

When I offer tool and product reviews here in the newsletter, I almost always have tested the product to ensure it does what it says. Here's an example of a time I've not done this. The reason why is the tool is so caveman simple, I already know it's going to work. And work WELL.

Bucket ApeHave you ever grouted ceramic tile? Let's say a large floor. You then know that part of the job is emptying out the water bucket countless times in a vain effort to keep the rinse water clean. The cloudy water in the grout bucket is part of the reason there is always a grout haze on the tile.

Imagine if each time you rinsed your sponge in the bucket there was NO GROUT in it. How is that possible you ask? Easy. The Bucket Ape allows you to transform a five-gallon bucket into a crystal clear rinsing station right where you're grouting.

A water hose feeds water to the bucket and a threaded drain fitting at the bottom side of the bucket connects to a second hose that pipes the water outdoors. DUH! As the water flows into the bucket, you get to rinse your sponge completely clean each time. It's a tile setter's dream tool. But wait, it gets better. Do you have a septic system like I do?

This tool is PERFECT for cleaning paint brushes and rollers for anyone, like me, on a septic system. You don't want to ever put latex paint into a septic system or a leach field. I so wish I had this great tool this winter while I was painting the kitchen.

The inventor has set up a special page at his website where you can get a discount. You can buy the entire kit or just the parts to make your own Bucket Ape. If you have scrap hoses around and a bucket, all you need is the Bucket Ape tray and the special fitting for the drain hose.

If you do buy from this link, I do get a very tiny commission on each sale. I only do this with products I really believe in.

 

AsktheBuilder on Facebook

AsktheBuilder on Facebook Do you use Facebook? Here's some of the stuff we discussed in the past few days at the AsktheBuilder.com Facebook Fan Page:

http://www.facebook.com/askthebuilder

  • I posted another mystery photo that you had to guess what it was.
  • Luke commented about my past column on Tankless Water Heaters
  • I helped James cut his patio blocks.
  • I shared how I got a grease stain out of a new marble top.
  • and MUCH more.

Become a fan and you'll get the free tips every time you login to your Facebook page!

 

Rusting Gutters

Lloyd Adams from Memphis, TN wrote to me:

"My wife and I built our house 22 years ago. The roof is good for awhile longer, but my galvanized gutters are rusting and leaking causing obvious problems. The gutter replacement job is more pressing, but I hate to install new gutters only to have them damaged when the roofers do their thing in a couple of years. Is this a needless worry, or should I go ahead and have the roof work done a bit early to spare potential damage to the gutters?"

Lloyd, I'm wondering if it's possible to salvage the gutters. If the rusting is not too bad such that the metal is paper thin, I'd use a special rust primer paint formulated to stick well to rust and then add a second coat of finish paint on the insides of the gutters.

Be sure to clean them well with soap and water to get all the dirt out before you paint. Once the paint is dry and cured, that can take two weeks, I'd coat all the soldered seams with the special sealant that's used on aluminum gutter joints. That will stick well on top of the paint. I love the sealant made by Alcoa.

 

Helping You

I need help from you once again so that I can do a better job of making your life easier. Here are some facts:

Tens of thousands of people come to AsktheBuilder.com each day. No doubt each and everyone has a problem. They sure as heck aren't coming to randomly surf my website.

I have thousands of pages of information at my AsktheBuilder.com website. So much information, that it's HARD for you to quickly find the tens of thousands of answers that are there.

If you're like most I talk with, your life is getting more complicated each day. You don't have the time or patience to look through all my content to get to the answers you need.

I get many emails each day with people asking pretty simple questions, but they want the Staples Office Supply store EASY button. If you're one of these people, you just want the quick answer. Right? I don't blame you one bit.

Here's an example. Carol B., from Cincinnati, OH, contacted me several days ago. She had a new concrete slab poured and it developed a crack. She was getting conflicting information about why it happened, who's fault it was and most importantly, WHAT could be done now to fix it.

All of that information was at my website. I've written extensively about it. But Carol was too busy, frustrated, or didn't have the patience to sift through my stuff to find out what to do. I understand that. Lately, I've been in the same mood and have little patience when faced with dilemmas.

After thinking about Carol's situation and knowing the answer was there for her, I had an epiphany.

What if Carol had seen at my Ask Tim page this announcement:

Do you have a problem? One of my 3-Minute Answer Guides could Solve Your Problem Right Now!

You click through and discover there's an Instant Download guide that you can read in 3 minutes or less. The document covers the causes of the problem, how it could have been prevented and the best part - SOLUTIONS to the problem that work.

What do you think about this? Would you like simple documents like this?

Would you take this SHORT survey to help me flush out this idea?

There is a place in the survey where you can tell me WHAT quick guides you want to see.

 

Washington DC Meet-up

It looks like I'll be in Washington DC again on May 24th with about three hours to kill late afternoon. If you're interested in meeting again and chit chatting, let me know.

 

Stain Solver Sweepstakes (Now over!)

We're having a new sweepstakes for Stain Solver! Go here for the details.

You could WIN a lot of Stain Solver. Better go look at this.

 

Latest Columns

Here are some columns I've loaded to the website. I really NEED your help.

When you read a column, note the SHARE button at the top near the headline. Could you do me a huge FAVOR and Share the column if you're on Facebook or Twitter? It will really help me if you do this.

Also, note at the BOTTOM of every column, you can comment to your Facebook friends if you discovered something in the column. That also helps me spread the good word to all that AsktheBuilder.com exists!

http://go.askthebuilder.com/CondensationProblems

http://go.askthebuilder.com/ConcreteRepair

http://go.askthebuilder.com/HardwoodFlooring

http://go.askthebuilder.com/TapingDrywall

http://go.askthebuilder.com/CentralVac

http://go.askthebuilder.com/KitchenRemodelingIdeas

 

Disclaimers and Other Stuff

I do product reviews frequently. Please read my Disclosure Policy to understand the relationship between me and the companies that make the products or offer the services I review.

PERIODIC OFFERS: This is a free newsletter filled with thousands of dollars of advice for your use and pleasure. From time to time I do offer you some of my products to help offset the time and resources I put into this newsletter. I hope that you consider this when you see me make you an offer.

If you wish to Unsubscribe, look all the way at the bottom for the Unsubscribe link. All you have to do is click it to stop getting this newsletter.

 

FOLLOW ME ON TWITTER

Friendly Question Reminder!

If you have a question for me, don't hit the Reply button just yet. Go immediately to my web site and type in the keywords about your problem into my Search engine. The search box is at the top of every page of my web site. You could have your answer in seconds if you do this! Please pay attention to all links you see at my web site. The exact products and services you often need are right in front of you, and you might be ignoring them.

 

April 25, 2011 AsktheBuilder Tips And Newsletter

If you're a NEW subscriber to my AsktheBuilder.com newsletter in the last five days, this is NOT a normal newsletter.

This is a very quick reminder that one of my annual promotions is about to expire.

Yes, the Annual Stain Solver Spring Sale is going to END at Midnight tonight April 25, 2011. You have only HOURS left to save not only money, but lots of your possessions.

Use this promo code:  ENJOYYOURBACKYARD    to get a 25 percent discount off our normal pricing.

If you're a long-time subscriber, you know three things:

  1. Stain Solver oxygen bleach is perhaps the best stain cleaner out there.
  2. You know Stain Solver is as green as can be. It's made in the USA from USA ingredients that are food-grade quality. You can't get better than that.
  3. Stain Solver cleans hundreds of stains.

Just last week, we got dramatic before and after photos of how Stain Solver was used to clean grape jelly from brand new seat cushions.

Yes, it's an amazing product. Don't miss out on this sale.

Go here to discover all the facts about Stain Solver:

http://www.StainSolver.com

Thanks!

Tim Carter
Founder -
www.AsktheBuilder.com and StainSolver.com

AsktheBuilder.com
100 Swain Road
Meredith, NH 03253, USA

Pex Plumbing Tips

pex plumbing

This is PEX tubing. I'm using a trouble-free UPONOR compression ring to make a connection. WATCH the video below to see it happen in seconds. Copyright 2018 Tim Carter

Connect PEX in Seconds - No Experience Needed!

This column was SO GOOD that I shared with the 31,000 subscribers who read my April 14, 2019 AsktheBuilder Newsletter.

DEAR TIM: Money is very tight in this current economy and I just can’t afford to hire a plumber to install new water supply lines in my home. I’ve seen the pex piping and feel it's the way to go as there are no soldered joints hidden in the walls.

Is it hard to install pex plumbing tubing? Can you share some secrets and tips? Am I crazy to think that I can be successful doing this? Dan G., Belle Mead, NJ

Related Links

Cut PEX Tubing in One Second or Less!

Prevent Frozen Pipes Using PEX - The Only Way to Go!

DEAR DAN: Not only is money in short supply right now for many, but I feel it's also going to get worse. This is going to cause many to jump in and do home repairs and remodeling not because they want to, but because they have to.

Free & Fast Bids

CLICK HERE to get FREE & FAST BIDS from local plumbers who can do PEX in case you're afraid.

There's lots of opportunity here - to make mistakes and to build confidence. Let's put you in the second group.

pex plumbing

It's important to realize that some cities and towns don't allow unlicensed people to work on the potable water supply systems in their homes. Keep in mind if your home is connected to a municipal water system, water, in certain situations, can flow out of your home and into the water mains outside your home.

If you've made connections to the system that allow polluted water to flow into the water pipes outdoors, you can make many sick. It's serious business.

One Practice PEX Joint and You're a Pro!

Let's assume you're allowed to do the pex plumbing installation work. I feel, with a little practice, you can be successful doing this major job. There are just a few areas where you'll need some sweet skills to ensure you don't have a leak.

Let's talk first about the many advantages of pex tubing and pex plumbing fittings. As you've already noted, since the pex piping is similar to electrical wiring, there are no joints in the pipe if you decide to install a separate pipe to each fixture from your main mechanical room where the water supply enters your house. That one characteristic of pex is an enormous time saver.

PEX Plastic Has a Memory

The pex tubing I've worked with, and had the best success with, is a special plastic that has a memory. Don't ask me how they figured it out, but when you stretch the material it fights to go back to it's original shape and size.

This property allows the piping and little compression collars to grab tightly onto the knurled surface of the male adapter fittings. This is what creates the leak-free connections between the pex tubing and a manifold or a valve at the end of a run.

PEX Expanding Tool - Just Get Hand-Powered One

To stretch the piping, you need a special tool that has an expanding cone tip. As you crank the tool, this cone expands the plastic.

pex hand expander

Here's a PEX hand expansion tool. It's hundreds of dollars cheaper than a power tool. CLICK THE PHOTO now to have this delivered to your home.

The warmer the pipe is, the easier it is to accomplish this. Cold temperatures cause the plastic to react sluggishly. This means it expands slower and goes back to its original size slower.

These special tools come in both hand powered and a sleek cordless electric tool that's very handy. You'll have to get one of these tools to do the job, so give a serious look at the cordless tool. Once you've completed the job, you can sell the tool online if you desire and get back probably 65 percent of the price you paid for it.

Connect PEX Using the UPONOR System

I have PEX in my home and it's the UPONOR system. It has these caveman simple compression collars that keep all joints leak-free. Watch how SIMPLE and FAST it is to make a connection:

Main Manifold May Stretch Your Comfort Level

The only place I can see you having problems is installing the two manifolds in your mechanical room. These are usually made from copper and have a shutoff valve at each port where you connect a water line. You'll have to securely attach the manifold to the wall and do some great soldering to connect the manifold to your water supply.

Some plumbers are moving away from the manifolds and installing pex piping like traditional water supply lines. In these cases you do end up with joints hidden behind walls.

CLICK HERE to get FREE & FAST BIDS from local plumbers who can do PEX in case you're afraid.

If you decide to install your system like this, you need to be very conscious of water pressure and friction losses. You'll have to install a 1-inch main trunk line that eventually downsizes to 3/4 inch and then 1/2-inch pipes that supply each fixture.

Employ Best PEX Practices

Be sure you follow all best practices when working with the pex piping. I would absolutely read any and all information that the pipe manufacturer has available. Be sure you don't pinch the pipe. Drill holes that are large enough for the pipe to pass through easily.

You also need to be aware of all the limitations concerning drilling and notching structural framing members. You just can't go start drilling large holes in floor joists. You can't notch floor joists.

The building code often contains good illustrations that show you exactly what you're allowed to do without compromising the structural integrity of your home. Check what's on the other side of a wood member before drilling. You could penetrate a wire or a gas line!

Practice First With PEX - So Simple

Finally, I would highly recommend testing your skills before you advance to putting the pipe and fittings in your home. Create small test joints where you connect a pex pipe or two to actual shutoff valves.

Then connect these short test pipes to your existing plumbing system. See if you have any leaks. Be sure you understand how to completely expand the pipe, rotating the tool as you expand the plastic and then quickly install the pipe and compression collar over the male end of the adapters before the pipe returns to it's original size.

Don't hope that you have leak-free joints. Remember, hope is the emotion of last resort. You hope for something when you can't control the outcome. In your case, with practice, you can control everything!

CLICK HERE to get FREE & FAST BIDS from local plumbers who can do PEX in case you're afraid.

Column 880

April 20, 2011 AsktheBuilder Tips And Newsletter

What's in This Newsletter?

Latest News
Deck Stain Test
Water Heater Pilot Light Outages
AsktheBuilder on Facebook
Stain Solver Sale
Snow & Ice Creating Roof Noise
Boring but Necessary Stuff

Welcome if you're a new subscriber. If you like this newsletter, feel free to forward it to as many of your friends as you wish.

Latest News

If you're a new subscriber in the past 14 days, you're unaware that I was pretty sick about three weeks ago. At the end of March, I was afflicted with a nasty case of the shingles. I'm on the mend, but it really put me behind.

I want to thank you if you sent me Get Well thoughts. I got so many emails that not only did I not have the energy to respond to all, but it just was impossible to answer you personally. I hope you understand.

You may have been one to slightly scold me about the lost opportunity to advise others about the vaccine or preventative medication that's available. Bottom Line: Next time you're at your doctor, ask her/him if you qualify for the vaccine or drug. I believe there is one if you've never had chicken pox - the source of shingles, and there is a different one that can be administered if you have had chicken pox.

All you need to know is that you don't want shingles on your body. They work great on your home, but you don't want them ever on your skin.

I'm getting much better. My scalp, at this point, feels like I have a medium sunburn. It's still sensitive to touch, but the extreme pain is gone as are the debilitating flu-like symptoms.

Deck Stain Test

I'm gathering the top semi-transparent deck sealers right now preparing to create a massive side-by-side test of the top brands. This is an offshoot of the test I did last year on my dock.

This morning I met with the factory rep for Valspar, Maribeth, and she was kind enough to give me two samples of their top-of-the-line deck sealer.

So here's the BAD news. The test results will NOT be available until next May. I want to do a year-long test. I'll have the results for you next Spring. Wait till you see the photos and how I document each step of the way.

I'll be testing the products on both weathered treated lumber and cedar decking.

Water Heater Pilot Light Outages

I've been receiving a rash of complaints about water heater pilot lights going out. Two weeks ago, I went to two of the top water-heater manufacturer websites and used the Contact Form to get someone from each company to talk to me.

Can you believe that I've yet to hear from one of the companies, and the other one just called back today?

If you have a company website with a contact form, I beg you to be more responsive. If you can't respond in 24 hours, then take down the contact form from your site.

What we do here at AsktheBuilder.com is review the incoming messages each day. Complaints and media requests are handled immediately. Questions we get are put in to the queue to be answered on a first-come first-served basis.

What You Missed on the AsktheBuilder Facebook Fan Page

AsktheBuilder on FacebookEach week I try to recap what happened in the past week on the AsktheBuilder Facebook Fan Page. If you're not on Facebook getting my updates, you should be. It's FREE. If you don't want to join Facebook, no worries, you can STILL go to the link just below and read all the tips for FREE.

If you're on Facebook, all you do is go to the fan page and click the Like button to get the updates.

www.facebook.com/askthebuilder

Here's a quick recap of what happened:

  • I helped Greg put up some wall sconces in his NYC apartment.
  • Joe, who lives near Cleveland OH, wanted to know the best roof shingles to buy.
  • I did a quick review of the Bosch PS50-2A Multi-X cordless tool. Woo Hoo!
  • I upload a photo of some cool wood bead board panels that I installed on a Sub-Zero refrigerator.

I really urge you to get on Facebook and Like my Fan page. There's lots happening there that you're missing. Some of it could save you lots of time and money!

Stain Solver Sale and Distribution News

My illness has caused me to delay the annual Stain Solver Sale. Before we get to the sale announcement, I desperately need your help.

Are you a satisfied Stain Solver customer? Could you please go to www.amazon.com and search for Stain Solver?

We've been selling it there since last September and got fantastic ratings with comments. But a month ago, we uploaded all the new photos and the NEW sizes of Stain Solver.

We didn't realize that would wipe out all of the past great comments customers left. It's really hurting us not having the comments. Would you please invest just 5 minutes of your time and go there leaving us a comment and telling a short story of what Stain Solver cleaned for you? Thank you so very much for doing this.

Now here's the sale information:

Everything about Stain Solver is NEW except the magical powder in the containers. We've not touch the awesome formula that makes Stain Solver, in my opinion, the absolute BEST oxygen bleach on the market.

Stain Solver logo
But the containers are new, the logo and labels are new, the boxes are new, the website is new.

So here's the sale news. First, in all the years of selling Stain Solver, sixteen I believe, I can't ever recall a discount this big.

I'm offering a 25% off coupon in honor of the outdoor cleaning season to use on decks, patios, siding, roofs, patio furniture, umbrellas, driveways and lawnmowers.

Because the discount is so big, it only lasts until midnight on the Monday after Easter (April 25, 2011). That's LESS than a week away! I'm sure there are those on some vacation and who will not see this email until Monday morning.

To get the discount, use this Promo Code:

ENJOYYOURBACKYARD

Go here to see the new Stain Solver website and all the things it cleans. You'll regret it if you pass on this sale. If you're a subscriber that's been around for years, you know I don't do these deep discounts every month.

I urge you to buy as much as you can afford. Wait till you see the EASY-OPEN containers that we've switched to. You're going to love them.

SS02 Stain Solver Finally, we are starting to place Stain Solver in specialty stores. If you want to SELL Stain Solver in your store, it could become a nifty profit center that you don't currently have.

I've been starting to visit stores here in NH that sell red wine, pet supplies, hardware, ceramic tile, linens, kitchenware, baby clothes, etc. Remember, Stain Solver gets out just about ANY organic stain in minutes.

If you work in one of these stores or own one, you'll want to have our gorgeous 2-pound bottle with the retro metal lid right at the cash register for all to see. It puts people's head on a swivel when they see it.

Go here for details to become a reseller of Stain Solver.

Snow and Ice Creating Roof Noise?

Nicole Carey of Worcester, MA emailed me the following question:

"A large amount of heavy snow and ice built up on the roof of my 4-year-old town home.  The condominium management company never used preventive measures to remove the accumulated snow.  Now my roof creaks every time there is a strong wind.  The creaking happens across the entire second floor.  Should a structural engineer look at the roof?"

Nicole,

I don't feel there is any need to call in a structural engineer. I would expect that your roof has been constructed to the minimum requirements for your area anticipating the snow and ice load.

The noises you hear could just be the structure reacting to wind loads. That's perfectly normal. If your house is of wood-framed construction, it can actually move slightly in response to wind loads. This movement creates noise. Almost always the house springs back to it's original position.

Just start monitoring your walls and ceilings for cracking. If you see cracks start to appear and they grow, then it's time to call in an engineer.

Boring but Necessary Disclaimers and Other Stuff

I do product reviews frequently. Please read my Disclosure Policy to understand the relationship between me and the companies that make the products or offer the services I review.

PERIODIC OFFERS: This is a free newsletter filled with thousands of dollars of advice for your use and pleasure. From time to time I do offer you some of my products to help offset the time and resources I put into this newsletter. I hope that you consider this when you see me make you an offer.

FOLLOW ME ON TWITTER

Friendly Question Reminder!

If you have a question for me, don't hit the Reply button just yet. Go immediately to my web site and type in the keywords about your problem into my Search engine. The search box is at the top of every page of my web site. You could have your answer in seconds if you do this! Please pay attention to all links you see at my web site. The exact products and services you often need are right in front of you, and you might be ignoring them.

AsktheBuilder.com
100 Swain Rd
Meredith, NH 03253, USA

Apron Sink Video Part 2

Hi, I'm Tim Carter of AsktheBuilder.com. This is part 2 of the Herbeau Apron Sink Video series. This video will show you the sink installed and more importantly, how it is supported.

In case you missed it, here is the link to part 1 of this series - Apron Sink Video Part 1.

Look at this. The apron sink is installed in the sink base cabinet. This sink cabinet before we started had a solid wooden front. Then the front was marked and a "U" shaped slot was cut out of the cabinet front. This slot has to match the apron sink. This is very important and takes some time. But if you do the measurements correctly, you will have no issues.

At this point, the sink appears to be floating in midair. How is it supported? I will show you. If you look down at the back of the sink, you will see a piece of plywood. That plywood extends completely underneath the sink, and it goes completely side-to-side of the sink base cabinet.

If you look under the plywood, you will see that it is held up by a 2x4 on either side of the sink base cabinet. These 2x4s are screwed into the side of the cabinet. The plywood is 3/4" thick and cutouts had to be made for each of the sink strainers. That is the support system for the apron sink.

That is what keeps the apron sink from dropping down into the cabinet. It is not hard to do. Just need to take a few measurements to match the sink. Remember the height of the plywood is a function of the height of the sink.

In this view, you can see the top of the sink. The top is flush or just slightly below the height of the cabinets on either side of the sink. That is very important. You don't want the sink to be higher then the cabinets on either side. If you install a stone countertop, like will be installed here, that could create a void on either side and if someone puts pressure on the countertop, it could crack. So the little gap from the sink being slightly below the surrounding cabinets, can be caulked with a black silicone caulk and no one will even know they are there. In addition, this will seal the sink so water can't get under the countertop and create rot problems.

So installing an apron sink is really simple. Use a 3/4" thick plywood support board and make sure the 2x4s are securely screwed into the cabinet sides. Do this and your apron sink won't fall down into the cabinet below. Or the basement!

Synthetic Canvas Tool Bag

DEAR TIM: I want to buy my husband a tool bag or tool box to surprise him. His tools are always scattered about and he wastes so much time looking for them. I assume you've had all sorts of experience in tool organization, so can you tell me what's worked best for you? My feeling is that if it works for you, it will be a dream-come-true for my husband. What's your favorite tool bag now and why? Meredith B., Greenville, SC

DEAR MEREDITH: You hit the nail on the head alright, as I've tried just about every tool organization product known to man. In fact, I still have the gray metal Craftsman tool box that was my dad's. I estimate that box to be close to 50 years old. It still has the logo plate on it.

This is a deluxe synthetic canvas tool bag that will make you more productive. PHOTO CREDIT: Tim Carter

Let's talk about the traditional tool boxes first before I share what my favorite is. What I don't like about the traditional tool box is the lack of internal organization. Some late-model tool boxes tried to create little compartments in the tray for tools, but for me, those never worked. If you fill up the tool box with tools of all sorts, they just lay on one another and you're constantly digging out tools to find what you need.

Not only is this a waste of time, the tools start to get worn from rattling against one another. It's not much different than throwing clothes into a closet and then rummaging around the pile to find what you need. When you hang clothes up, you can see them and put your hand on that blouse or pair of pants as soon as your eye sees what you want.

Nearly two decades ago, inventors started to deal with this rumble that was resonating from the toolboxes. I can clearly remember seeing a first-generation tool organizer that fit over a 5-gallon bucket like a saddle on a horse. This organizer had all sorts of different-sized pockets for all sorts of hand tools. It was a great first step towards making tools visible and accessible.

 

Stop - Check this out! Tool Bag
Do you want the EXACT tool bag I wrote about in this column?

VETO PRO PAC Model LC Tool Bag

This is an affiliate link. If you purchase this item, Amazon will pay me a small commission.

The only problem with this open method was that the tools could get wet or dirty as they had no covering on them. Although this was not a deal killer for me, it was just two steps forward and one step back with respect to protecting the tools. The bail handle on the bucket was also problematic as the bucket became filled with heavy tools.

If you jump in the time machine and go back about 12-15 years, you'll discover the first generation of soft-sided tool bags that had all sorts of pockets, chambers, etc. for tool storage. One of my favorite was an actual backpack that was made to carry hand tools.

One of the latest soft-sided tool bags that I've tested really has got my attention. I'm convinced your husband will love it. It's shaped like a backpack, but it opens on both the front and the back. The flaps just zipper up and down and fold away using handy snaps so the flap doesn't touch the floor or the ground.

You can put just about any hand tool you can imagine in this deluxe synthetic canvas tool bag. They come in different sizes depending upon your husband's tool collection. I can see owning one, two or three of these bags and setting them up for each project discipline.

For example, one part of one side of this tool bag could be dedicated to electrical tools. You'd easily take up space with your linesman's pliers, wire stripper, needle-nose pliers, circuit testing tools, etc. The other half of that side of the tool kit might be dedicated to plumbing tools.

I can see one entire tool bag that's just for carpentry tools. The list of tools you might put in the little pockets is endless. Nail sets, screwdrivers of every type, chisels, plumb bobs, torpedo levels, tiny pry bars, etc.

Your husband is going to love the tool bag if you get the one I'm now using. Of that there is no doubt. I love the padded shoulder strap that comes with it. When not in use you park it next to the tool bag handle with common hook and loop connectors. This keeps the strap off the ground and out of the way.

You can look at both open and closed tool bag solutions. The open tool bags have come a long way since the simple ones that overhung a bucket. Any number of these bags have designs, both open and closed, that work perfectly for every tradesman.

For example, I know the one bag I use would be perfect for my heating and air-conditioning contractor. He has all sorts of specialty hand tools, nut drivers, and specialty tools he uses to service AC units, furnaces and boilers. The bag I use now would keep all of the tools he needs protected, dry and right where he needs them.

Electricians, maintenance men in hotels, elevator mechanics, refrigeration contractors, plumbers, etc. all need tool bags like this that help them keep their specialized tool organized, clean and protected. If you know of one of these craftsmen, suggest they look at the new tool bags to see if they don't feel it will help them in their everyday work.

Stop - Check this out! Tool Bag
Do you want the EXACT tool bag I wrote about in this column?
Get it here.

VETO PRO PAC Model LC Tool Bag

This is an affiliate link. If you purchase this item, Amazon will pay me a small commission.

Column 878

April 5, 2011 AsktheBuilder Tips And Newsletter

What's in This Newsletter?

Latest News
No Austin Meet Up
Finish Carpentry Saw Blade Test Soon
Attaching a Mantle to a Brick Fireplace
More Next Week
Boring but Necessary Disclaimers and Other Stuff

Latest News

Our bodies talk to us. But sometimes we don't listen. Well, let's say I wasn't listening. You can bet I'll pay attention next time.

Last Monday, I flew to Los Angeles to begin a 12-day business/pleasure trip. Three days ago, I was back in New Hampshire in writhing pain.

Recreating what happened, the early signs started to happen last Sunday, the day before I left. That morning, while combing my hair after my shower, I noticed some tenderness and a few bumps on the left-rear quadrant of my scalp. Big deal, maybe it was a pimple or two.

When I got to Las Vegas on the first leg of my long flight from NH to LA, I noticed my neck was stiff - more than usual. I blamed that on sleeping on the plane without using one of the silly looking pillows.

Last Tuesday, the bumps on my scalp became worse and I started to have these weird pulsating stinging pains. I thought that was just a muscle spasm due to me straining my neck while sleeping on the plane.

I called my doctor and made a mistake by answering a question wrong. I failed to really think through that all the pain and bumps were only on one half of my body. Perhaps I was already in enough pain, I missed the question. That caused a one-day delay in the diagnosis.

The following day, Wednesday, the pain was getting worse, so much so I only got a few hours sleep. I called the doctor again, as something was wrong. The stinging pains were getting more frequent and worse. The best I can describe in getting stung by 10 wasps at the same time. It happens without warning.

If you're in the health field or you've had what I have, you've already figured it out. Shingles, and not the ones you put on your house. I've got shingles. Go Google this and read up on it. You don't want this happening to you. Not ever.

By Saturday morning, I couldn't stand it any longer. My friends drove me from Las Cruces, NM to Albuquerque, NM. This was the best option to get me on a plane to get me home to NH as quickly as possible.

I'm still suffering today as I type this, but I may have seen the worst. Let's hope so, as the symptoms can continue for weeks or months.

No Austin Meet Up

I was supposed to be in Austin, TX today beginning a three-day conference. I was going to try to meet with you tomorrow for lunch. Obviously that's not going to happen. I'll get back there one day.

Finish Carpentry Saw Blade Test Soon

I just ordered three saw blades from IRWIN Tools to begin a precise test to see which blade produces the finest cuts with trim lumber where you just can't afford any fuzz or tiny splinters. I hope to have the results available to share with you very soon.

Attaching a Mantle to a Brick Fireplace

French Cleat VideoAlbert Daughtridge of Fort Lawn, SC emailed me the following question. He must have watched my French cleat video I did a few years back about this time-tested hidden method of attaching things to walls:

If the newsletter sign up form slides into the window as the video plays, wait a few seconds and an X with a circle will appear in the upper right corner of the form. Click that and it will close the window. I have a cookie set to make that NOT happen, but the cookie may have expired on your computer.

But Albert must have sneezed during the middle of the video because I clearly show you can make the cleat from metal.

Here's what Albert asked:

"How do I attach a 9 1/4"W x 3 1/2"H mantel to a brick chimney. The solution must be a non-combustible attachment to meet code.  So a French cleat will not work."

Albert, metal meets code and it absolutely will work in this case. You just need a fairly stiff piece of sheet metal, perhaps 16 or 14 gauge.

More Next Week

www.facebook.com/AsktheBuilderI've run out of energy already this morning because of these wicked shingles. I'll have more for you next week. Oh, the meet up in Montrose last week was tons of fun. I discovered much that's going to help me improve the newsletter and the website. PLEASE come out to any meet up I have if you can. If there's not one near you, would you consider coming to a one-day event? Let me know. There's a photo and short video of last week's meet up on my AsktheBuilder Facebook Fan Page.

www.facebook.com/AsktheBuilder

Time for me to go lay down.

Tim Carter
Founder - www.AsktheBuilder.com

Do it Right, Not Over

Boring but Necessary Disclaimers and Other Stuff

I do product reviews frequently. Please read my Disclosure Policy to understand the relationship between me and the companies that make the products or offer the services I review.

PERIODIC OFFERS: This is a free newsletter filled with thousands of dollars of advice for your use and pleasure. From time to time I do offer you some of my products to help offset the time and resources I put into this newsletter. I hope that you consider this when you see me make you an offer.

FOLLOW ME ON TWITTER

Friendly Question Reminder!

If you have a question for me, don't hit the Reply button just yet. Go immediately to my web site and type in the keywords about your problem into my Search engine. The search box is at the top of every page of my web site. You could have your answer in seconds if you do this! Please pay attention to all links you see at my web site. The exact products and services you often need are right in front of you, and you might be ignoring them.

AsktheBuilder.com

100 Swain Rd
Meredith, NH 03253, USA

March 29, 2011 AsktheBuilder Tips And Newsletter

What's in This Newsletter?

Latest News
Retaining Wall Design
Deck Cleaning Season
Leveling a Floor
Montrose, CA Meet Up
Austin, TX Meet Up
ATB Survey
Disclaimers & Other Stuff

Latest News

I'm typing this at 38,000 feet as I fly Southwest 897 from New Hampshire to California. I'm starting a 12-day business / pleasure trip that ends up in Austin, TX. Lisa, the humorous blonde flight attendant on this leg of the trip joked about Bearnaise sauce on my fantasy meal that I asked her about. She said it would be exceptionally good today. Three hours into the flight, I'm still making do with a small packet of Lorna Dunes while I wait on the steak and mashed potatoes on this 5.5-hour flight into LAS.

My long-sleeved tie-dye shirt must have set off the TSA profiling this morning. I was pulled from the line and screened for explosives. I passed with flying colors even though hours before I was handling ammo loading a gun. Looks like my pre-dawn shower saved me! Go Dove soap!

Too bad I don't use an iPhone any longer. If I did, I could really use the new California Essential Guide application. It's a handy travel app loaded with video content created by a subscriber to this newsletter, Veronica Hill. Veronica used to edit and publish my weekly column when she was the Features Editor of the Victor Valley Daily Press.

Veronica has transitioned from the newspaper industry to the Internet. She's become the go-to authority on California travel. If you plan to come to the Golden State to see the sights, don't do it without her new app. Hurry Veronica, make a version for my Android phone!

Retaining Wall Design

Is a retaining wall job in your near future? My retaining walls up in New Hampshire are starting to peek out from behind the snow. Remember that gravity wants to tip them over. What's more the taller the wall, the tipping force grows exponentially. Consider leaning the wall back to account for this. We call that batter.

If you're building the wall from just stacked stone, the taller the wall the larger the stones you need to use to make the wall last longer than you. Be sure to bury the first course of the wall into the soil about one-third the height of the first row.

I've got many more tips for you about retaining wall construction at my website. Take some time and read the past columns there.

Deck Cleaning Season is Here

On Sunday, Kathy and I had to drive our youngest daughter back to URI as spring break was over. It didn't seem like spring as we pulled up the driveway past piles of snow still 4-feet high.

But think about it. In just 9 weeks or so, the boats will be zipping up and down the lakes up here and everywhere for the official start to the summer - Memorial Day weekend!

If you're going to clean your deck to seal it, you surely want to consider doing it with my Stain Solver oxygen bleach. It's not toxic like chlorine bleach. It's safe for all your plants and landscaping. It won't turn the wood white like chlorine.

Here's the BEST part. We've switched to all-new packaging, sizes and pricing but I still have a few of the older, less-expensive size of Stain Solver at my AsktheBuilder.com shopping cart.

To clear those out of the warehouse, I'm having a honest-to-goodness clearance sale. If you want Stain Solver for just about the lowest price you'll ever see again, now is the time to buy it.

The quantities of each size are limited. When they sell out, you'll see the new size on the page with the higher price. There's no need for a promo code as I've already discounted them 20 percent.  Go NOW and get the last of the old containers at this amazing price.

Note: This sale is only at the AsktheBuilder.com store. If you go to www.StainSolver.com, you'll not see the special pricing. You can go to the Stain Solver website to learn all the cool stuff about it, but use this link to get the special pricing.

Leveling a Floor

Gail and John visited me yesterday to look at my refrigerator I had listed on Craigslist. Once they discovered who I was, they had a question about a basement remodel job.

The previous homeowner installed a plywood floor on flat 2x4 sleepers that he didn't shim. The floor had more humps and dips than an old country road.

John was about to tear up the flooring to start over. I suggest an alternative. What about two quick coats of water-based urethane over the plywood and then mixing up some self-leveling floor compound? The urethane prevents water from entering the plywood that could cause it to swell and buckle.

They loved the idea. See what happens when you come visit me face to face? You get personal service to your home-improvement problems!

The Montrose, CA Meet Up

I may be meeting you for the first time in person in on Wednesday, March 30th! I've already got quite a few RSVPs for the informal meet up at the Coffee Bean and Tea Leaf in the center of downtown Montrose, CA at 1:00 pm.

It's located at the corner of Ocean View Boulevard and Honolulu Avenue. Some moms are bringing their sons, so there's no excuse for you not to be there other than work, distance or health reasons. My buddy Don Vandervort said he'd show up so if you have any home-improvement question, we'll be able to help you.

The Austin, TX Meet Up

On April 6th at Noon, I'll be doing another meet up. This one will be in downtown Austin, TX within walking distance of the Hyatt hotel. I'll decide where it will be in a few days and send that out. Did I say how much fun the meet ups are? I'll post a photo of the Montrose one the AsktheBuilder Facebook fan page.

Here's what you missed in the last few days by NOT being an AsktheBuilder fan on Facebook:

We did another guessing game about a unique metal bar I took a photo of. I helped Kelly determine how fast to jack up here sinking home. Elice had a mystery clunking noise in her sump pump. We solved that together. Kristin had a wallpaper question about her new post and beam home. And much, much more!

ATB Survey

Several days ago, I asked for your help. I'm doing a massive make over of the AsktheBuilder website. I'm not removing any of the content, but I'm interested in what you want MORE and LESS of.

The early results are absolutely unbelievable. You may have taken the time to share some real gems that will really help make the website better.

To put it mildly, the survey results are highly stratified. One thing's for sure, and this is nothing new, it's impossible to satisfy everyone.

I did want to share one quick fact with you. A few people commented on the unanswered questions in the Comments section below each column. Years ago I started to answer questions there and had to stop because it was taking hours and hours of time each day.

There is now so much traffic to the website that I could spend 24 hours a day and never get a lick of work done. That's why I put the announcement pointing you to the Ask Tim page if you have a question.

A member of my staff spends all day dealing with these questions and passes off the ones she can't answer to me. We at AsktheBuilder.com appreciate your patience when you use this free service.

Tim Carter
Founder - www.AsktheBuilder.com

Do it Right, Not Over!

Disclaimers and Other Stuff

I do product reviews frequently. Please read my Disclosure Policy to understand the relationship between me and the companies that make the products or offer the services I review.

PERIODIC OFFERS: This is a free newsletter filled with thousands of dollars of advice for your use and pleasure. From time to time I do offer you some of my products to help offset the time and resources I put into this newsletter. I hope that you consider this when you see me make you an offer.

FOLLOW ME ON TWITTER

Friendly Question Reminder!

If you have a question for me, don't hit the Reply button just yet. Go immediately to my web site and type in the keywords about your problem into my Search engine. The search box is at the top of every page of my web site. You could have your answer in seconds if you do this! Please pay attention to all links you see at my web site. The exact products and services you often need are right in front of you, and you might be ignoring them.

AsktheBuilder.com
100 Swain Rd
Meredith, NH 03253, USA

Fireplace Repair Options

DEAR TIM: I have an old rock fireplace that I hate. The built-in heat-a-lator has also stopped working. I want to change the rock face to one that’s wood. I have some extensive woodworking experience, so is it possible to make these fireplace repairs myself? Can I build a wood frame over the rock and disconnect the gas log lighter that’s in the firebox? Suzanne H., Richmond, VA

DEAR SUZANNE: This fireplace restoration is an enormous job. I always say that anything is possible if you have enough resources, which sometimes includes lots of money. This job, however, needs abundant skill, time and a deep knowledge of the building code.

The homeowner wants to transform the rock face into wood. It’s a daunting task fraught with problems. PHOTO CREDIT:  Suzanne Hofer

The homeowner wants to transform the rock face into wood. It’s a daunting task fraught with problems. PHOTO CREDIT: Suzanne Hofer

The quick answer is that it’s possible to do what you want. You can transform the exterior look of the fireplace. But I’d caution you about removing the gas log lighter. A future homeowner may want this convenience.

If you’ve ever seen how many masonry fireplaces are constructed, you’d immediately think of the way cars were built before the advent of unibody construction. Cars used to be built like trucks are today. There was a chassis or frame and the body skin of door panels, fenders, quarter panels, etc. all were bolted to one another then to the frame.

Fireplaces are somewhat like this. Modern masonry fireplaces often have a concrete block center core that contains the clay flue liners and the firebox made with high-temperature fire brick. The outer skin you see can be rock, brick, wood, plaster, drywall, etc. These materials are attached to the concrete-block center core.

Your challenge is to see what’s easier assuming you have a masonry fireplace that constructed with a block core: Remove the rock facing or build a code-approved wood frame out beyond the rock.

If you decide to attach your finished wood to a wood frame that’s attached to the rock, be aware the thickness of the wood frame and finished wood skin may cause the firebox starts to get deeply recessed into the overall fireplace. There could be an aesthetic dimension here that needs to be addressed. It could also be a building code issue.

Before you do one thing, you need to visit your local building department and get a copy of the current building code. Take photos with you and meet with the building inspector or the head of the building department. Remember, these are public employees and are our servants. It’s their job to assist you and answer your questions.

You want to be crystal clear on all the clearances that are mandated in the code with respect to the proximity of combustible materials to the firebox. Don’t leave this meeting unless you completely understand what the minimum requirements are. Make drawings there and have the building inspector sign them or otherwise approve your understanding.

You’ll discover quickly that the code talks about horizontal and vertical distances to things that burn. It also may have a section that talks about maximum overhang of combustible materials.

Once you have a firm understanding of these code requirements, take the time to draw a simple scale plan of what you’re allowed to do. See if is going to look right. You want to make sure you also do a side elevation as if you’re looking at the fireplace sideways. This will be on a scale that measures perhaps 1 inch equals 1 foot. You only need to draw from the hearth up to about 3 feet above the mantel. This will give you a good idea of the mass of the new exterior skin.

As for the heat-a-lator, you’ll have to determine if the fans are bad or if it’s some other electrical problem. If there are no fans and it’s just a gravity air convection system, perhaps you can determine why there is no or little airflow as you take apart the fireplace. It could have been poorly designed from the get go, and there may be little hope of making it work without a massive reconstruction effort.

You’ll have to incorporate a new stone material that surrounds the firebox and transforms to the wood. You may choose to use a natural stone like marble or granite for this. You can also use ceramic tile. We had one fireplace at our last home that had a green serpentine marble surround that complimented the walnut wood surround. Our living room fireplace had a traditional decorative ceramic tile facade just outside of the firebox.

All of these treatments usually need perfectly smooth surfaces to bond the tile or the stone to the fireplace core. You’ll have to engineer all of this into your plan before you start the job. This may require you to tear off all the stone to get to the central core of the fireplace. Be prepared to punt frequently as you’re entering unknown territory.

If you decide to build a frame on top of the rock, I’d strongly consider using lightweight steel studs. These don’t burn. If you need to add lumber to make nailing or screwing your finished wood to the frame easier, be sure to used fire-rated lumber that’s cut to fit into the steel stud channels. You can often find commercial-grade fire-rated lumber at specialty lumber yards. It’s been chemically treated so it doesn’t support flame except under the most fierce fire conditions.

You want to do everything possible to ensure an ember that could somehow get behind the finished wood doesn’t set the frame on fire as you leave the room unattended. Steel is your best bet.

Column 877