Aunt Margaret the Maven

Aunt Margaret

Let’s go visit Aunt Margaret,” my Dad said. If I’d had a mirror in front of me, there’s no doubt my eyes and grin were wider than an airplane-hanger door. Margaret was my Dad’s older sister, and she lived with my Uncle Louie in a majestic old home in North Avondale, an original suburb of Cincinnati, Ohio. Aunt Margaret was a fun aunt. Trips to her house were guaranteed good times.

Aunt Margaret was a magical woman. I’m not an expert in human genetics, but there’s not a doubt in my mind that my positive attitude, Peter-Pan maturity, and my-cup-is-overflowing outlook are directly related to her DNA.

This isn't the best photo of Aunt Margaret. She's on the left. She was the maid of honor at my Mom and Dad's wedding. This photo was taken at Aunt Margaret's house on Reading Road in North Avondale - an old Cincinnati, OH suburb.

Aunt Margaret always greeted me with a huge smile, a hug and something nice to say, except for those days when Uncle Louie had stretched her patience tighter than a banjo string.

margaret carter foltzer

Aunt Margaret on the right. She was 31 in this photo. What a piece of eye candy. WOWZA! I have no clue who the older woman is but she could be my grandmother!

Once my Dad and I got to Marge’s house, my Dad called her that, we entered through the back door into her huge kitchen with soaring 10-foot ceilings. I remember it was a Saturday and for some reason that always meant moist cinnamon coffee cake was somewhere on the counter. Margaret knew that I savored this treat and no sooner had I entered the room from the climb up the outside steps she inquired, “Timmy, how about a piece of coffee cake?

My face told her all she needed to know. Standing in the center of the kitchen she handed me a generous piece of the pastry. Not wanting to sit down, I immediately took a bite and crumbs exploded from the edges of my mouth landing on her spotless floor. She just laughed poking fun at her brother asking him if they never fed me at home. Aunt Margaret always teased my Dad, but it was all in good fun. That’s what most brothers and sisters do.

margaret carter foltzer

Here's Aunt Margaret fishing in Florida. No sunscreen back then!

Once I devoured the last bite of the coffee cake Aunt Margaret chuckled, “Well Timmy, you made a little mess. Let’s clean it up.” She didn’t get a broom or a mop out of the closet. In one quick motion, she touched the crumbs with the tips of her fingers and they stuck to her skin like nails to a magnet. I was dumbfounded. In my five long years on the planet’s face, I had never seen crumbs magically attracted to fingers like that. The floor was spotless and she just laughed. What was this mystic power that my Aunt possessed? Just like all professional magicians, she didn’t reveal her secret, but years later I figured it out.

My First Time

Aunt Margaret and Uncle Louie loved to entertain. I have crystal-clear memories of adult parties at their home. My sister and I would amuse ourselves running up and down the plush carpeted stairs to their second floor as the adults talked about money, politics, work and who knows what. The steps were unlike any I had ever seen. When you got to the top of the steps, the hallway went left and right. It was the coolest thing ever.

Margaret was all about appearances. She dressed to the nines, had gorgeous black hair and a drop-dead gorgeous smile. Although not full-figured, she was very attractive. She applied this same set of standards to the buffet of food at her parties. The sterling silver and cut-glass platters, bowls and silverware gleamed. They were filled with all sorts of scrumptious food and treats. The sideboard table in the dining room where they all resided was as crowded with people as opening day at the Reds baseball stadium.

One particular party she gently took my hand while no one was watching and whispered in my ear. “Timmy, I’ve got something I want to show you. Come with me,” the words escaped her lips like a puff of fragrant spring air. We walked across the crowded dining room to the sidebar table that was overflowing with food of all sorts.

Try this for me please,” she purred with a smile on her face. Aunt Margaret had never led me down the wrong path. I trusted her more than an explorer does a compass. But she was handing me the strangest white thing I’d ever seen, and it appeared to be covered in thick blood. I must have grimaced and pulled back, but with her lips inches from mine, she softly implored, “I know you’ll love this. Go ahead and take a bite.

Mustering up all the courage a kid can when presented with strange food, I gulped and didn’t disappoint her. After all, it was Aunt Margaret, I loved her, and she was looking deeply into my eyes as any temptress would. At that instant in time, I’m convinced she wanted me to eat that cocktail shrimp more than she wanted life itself. She knew how good they were, and she wanted to be the first person to show me.

I bit down into the ice-cold crustacean, and the cocktail sauce flavor set my mouth slightly ablaze. There was just enough horseradish in the ketchup to give the sauce a tangy flavor. The firmness of the shrimp was intoxicating, not to mention it was tasty. Aunt Margaret’s laughter undoubtedly was sparked by my eyes lighting up in response to the heat and taste. I’m sure my request for more intensified her chuckle.

Aunt Margaret was but one of my fun aunts. All three of her other sisters had great smiles, perky personalities and each took me under their wings in a special way. Thelma, Juanita, and Edna Mae were a bright spot in my childhood, but Margaret’s magical fingers are something I’ll never forget, much less her raven hair, sweet smile, and taste in food.

margaret carter foltzer

Even as she aged, Aunt Margaret was gorgeous. This photo was probably shot in the late 1960s at Aunt Juanita's 3rd wedding is my best guess.

As I’ve grown older, I’m convinced Margaret saw herself in me. I often have that same vision when I see children. You just seem to be able to predict what they’ll turn out to be. I wish Margaret were still alive today, so she could see if her intuition was spot on. Now that I think about it she didn’t need the proof - she already knew. God bless you, Aunt Margaret!

Coast G10 Flashlight

Coast G10 LED Flashlight in hand

Coast G10 | I don't have big hands. Look how the flashlight is a little longer and as wide as my biggest finger! But it's BRIGHT! You can get it in Black or Silver. CLICK or TAP HERE or the image to have one in your hands in days.

Coast G10 Flashlight - Very Small But Very Handy!

I had a chance to test out the Coast G10 LED that sports a cone-shaped inspection beam.

I loved it! It's a perfect prize flashlight to give to someone for their purse or pocket. It's about the size of a jumbo Tootsie Roll, so that's not big at all!

Coast G10 LED Flashlight

This little guy or gal is bright as can be. You can see things up to 65 feet away. That's plenty of time to throw a snowball, golf ball, or ping pong ball at the banshee you've highlighted. CLICK or TAP HERE or the image to get one now. This flashlight is SO AFFORDABLE!

Coast G10 LDE Flashlight

One AAA battery is all you need to turn night into noon. CLICK or TAP HERE or the image to astound your friends and enemies with your savvy buying skills!

Coast G10 LED Flashlight

One fresh AAA battery in warm temperatures should provide 2.5 hours of light. CLICK or TAP HERE to see if that's true. Don't use crap batteries. Consider rechargeable ones like I use.

 

 

 

December 9, 2019 AsktheBuilder Newsletter

Are you a new subscriber? Thanks for being here. It's my job to surprise you, as often as I can, with dandy home improvement tips and special prizes. A prize is just a gift and it can be something as simple as a past helpful column on my website.

Are you a subscriber that remembers when I had blonde hair? Thanks for staying on the list. You know I'll try to continue to aim the fire hose of money-saving tips at you week after week after week.

Christmas is Looming

Wow, Christmas is just a little over two weeks away! It's on a Wednesday this year and that makes for an odd week.

Are you looking to get that special someone some great tools?

CLICK or TAP HERE to see a list of some of my favorites. I add to this list from time to time.

Garage Floor Drains

Last week in the newsletter I made an off-the-cuff mention about my daughter's new house and how it had floor drains in the garage.

garage floor drain ideas
Who would ever think that simple statement would create a mini tsunami of email responses?

I decided to expand on the topic and directly and indirectly answered all the questions asked of me in the new column.

CLICK or TAP HERE to discover all you might ever want to know about garage floor drains.

REMEMBER, if you have a QUESTION, put it in the COMMENTS section at the end of the column. That way EVERYONE gets to benefit from my answer. The comments are moderated and you may not see yours appear for hours or a day. Be patient if that's not your strong suit.

Dandy Coast Small Personal Lantern

I had the chance to try out a very very interesting small personal lantern.

It's the Coast EAL13.

coast eal13

You might think this is some giant lantern that's the size of giant can of baked beans. Boy, baked beans with a touch of brown sugar, some Raye's mustard, and chopped onions with fresh steaming chicken wings sounds good, doesn't it? WHAT???? You've NOT HAD Raye's mustard????

Eating the many different flavors of Raye's mustard can be life changing. I've have a few life-changing encounters, so I speak with authority here, trust me. But I digress.

This is a midget lantern is just the thing you need for your car or truck or where you do desk work in case of a power outage!

CLICK or TAP HERE to discover more about this high-quality Coast product.

There are MANY MANY photos of this lantern in the above column. I highly recommend you read the captions below them if you're having a bad day.

Getting Old Stuff

Steve from Scarsdale sent me this photo:
Steve's Trex Railing

Here's what Steve sent me in addition to the photo:

"I have a deck railing made of a Trex early generation composite material. Part of the railing has gone missing. The railing and deck are from the same material and in good shape. Any idea where I can source some of this material/railing to make the repair?"

How would you answer Steve?

I told him to set up an ALERT on Craigslist because that's where I sold all my OLD deck railing and ALL of my first-generation TREX decking three years ago.

Local people were SO HAPPY to discover old stuff for sale as they needed it just like Steve does.

Don't believe me? CLICK or TAP HERE and have your curiosity satisfied more than you would be if you opened a box of Christmas prizes early!

That's enough for a Monday. I tried to get this newsletter to you yesterday, but walking on my Kahtoola microspikes on 3/4-inch of ice took priority.

Tim Carter
Founder - www.AsktheBulider.com
Certified Organic CLEAN MAN - www.StainSolver.com
Morse Muff Man - www.W3ATB.com

Do It Right, Not Over!

P.S. Tell me something. Did you know this SECRET way to unclog a toilet without having to stick the plunger in the gross water?

CLICK or TAP HERE and watch the video with the blue water in the bowl.

Let me know if you think this is a better idea! READ the comments below my idea. WATCH the video!!!

Stop Water Mess in Your Garage

garage floor drain ideas

Garage Floor Drain | This piping looks complicated but it’s not. You’re looking at two new garage floor drains, a simple running trap, and a surface clean-out for the trap! A garage floor drain is an excellent dream garage idea. (C) Copyright 2021 Tim Carter

DEAR TIM: I’m about to build a new home with both an attached garage and a separate free-standing three-bay garage. The house I grew up in had floor drains in the garage and they were wonderful. My builder has never heard of garage floor drains and insists on sloping the concrete floor so all liquids flow to the doors. I can see this will be a nightmare in the winter when ice and snowmelt from cars and trucks. What would you do if you were me and how do you install garage floor drains in your jobs? Steve H., Madison, WI

Have you run into the situation Steve’s facing? I can tell you I live his nightmare each winter here in my own home here in snowy New Hampshire. I didn’t build the house I live in and my garage doesn’t have magical floor drains like the house I grew up in as a kid. Water melts from my car and truck and puddles down at the closed garage doors. It’s a nightmare.

Is the Building Code a Set of Minimum Standards?

It’s important to realize the building code is a set of minimum standards. You can always build things better than what the building code mandates. The building code is revised every few years and I can tell you that some fantastic things have been forgotten or changed in past revisions.

CLICK or TAP HERE to get FREE BIDS from local plumbers who can install a garage floor drain.

I checked several citations of the International Building Code and there was language that garage floors must slope to the door so liquids drain to the door or to a drain. Another key point is that cities or towns can make their own revisions to the code. What’s acceptable in one town, may not be allowed in another city nearby. You always need to check with your local code official and see what you can do.

Did You Install a Garage Floor Drain in your Daughter's New Home?

This past year, my daughter and son-in-law built a new home on Mt. Desert Island in Downeast Maine. I specified that floor drains be put in the garage and made sure with the local building inspector, Ms. Angela Chamberlain, that she allowed this. Not only did she permit the floor drains, she indicated the water from the drains could drain to the surface beyond the house just like downspout water from the roof.

How are Garage Floor Drains Piped?

The floor drains in older homes were piped in almost all cases with a simple p-trap just like you might find under your bathroom sink. The u-shaped pipe under the drain created a water seal but it also allowed sand and dirt to accumulate fast. You had to be really careful in older garages so as to not clog the drain line past the u-shaped running trap.

What Kind of Garage Floor Drain Fixture is Best?

I installed modern side-outlet box drains in my daughter’s garage. These measure about 14 inches square and are about ten inches deep. The drain pipe exits out the side of the box drain and the bottom of the pipe is about 1.5 inches up from the bottom of the box.

This allows sand and grit to settle out and not be carried into the drainpipe leaving the box drain. However, you need to keep up with making sure this sand, dirt, and grit never get any thicker than the 1.5-inch catch area!

Do You Put in a P-Trap in a Garage Floor Drain?

Downstream from the box drains I installed a self-made p-trap using 90-degree fittings. I also used a tee fitting so I could create a surface clean out that rises up from one end of the p-trap under the slab.

This clean-out allows my son-in-law, or a future homeowner, easy access into the p-trap using the hose from a wet-dry vacuum. Should the p-trap get clogged it will be very easy to clean it out.

Is Car Oil a Pollution Hazard?

Some people worry about oil getting into the floor drains and it causing pollution of the ecosystem. That’s a valid concern if you have a massive oil spill in a garage. I maintain this is a rare occurrence. If you’re worried about oil pollution, you can install a commercial oil separator as part of your drainage pipe installation. And as for car and truck oil pollution, imagine how many gallons per day leak onto the roadways around your town or city from pesky drips from engines, transmissions, and hydraulic hoses.

Common sense also is required if you have a car or truck that has a tired engine or transmission. If these do leak small amounts of oil, for goodness sake lay out some cardboard to soak up the leaks and replace the cardboard once it becomes saturated. There are also dry granular products made to soak up oil spills. You see this product at many gas stations when someone spills diesel fuel or other oil products.

How Far Below the Floor Surface Should the Drain Be?

It’s very important to make sure the tops of the floor drains are about 2 inches below the primary level surface of the garage slab. The concrete contractor needs to create large shallow funnels around the floor drains.

The size of the funnel depends on the size of the car or truck. At the very least, the funnel should be a total of 10 feet wide and 22 feet long. Center the floor drains so they’re exactly under the center of where the car or truck will be parked in the garage.

What are Floor Drain Benefits?

Another side benefit of having garage floor drains is you can wash your car or truck inside on blistering hot days or in colder months should you live where it gets cold. You can purchase a special hose bib that has both a hot and cold handle just like any indoor sink. This way you can use warm water to rinse off your vehicle.

Column 1331

Garage Floor Drain Ideas

garage floor drain ideas

Garage Floor Drain Ideas | This is a simple illustration of a modern side-outlet garage floor drain. There's a small area at the bottom of the drain to capture sand, dirt, and debris so it doesn't clog the drain pipe.

Garage Floor Drain Ideas - Time Tested Technology

The inspiration for this column came from unexpected comments about a brief mention of garage floor drains in my December 1, 2019 AsktheBuilder newsletter and my December 9, 2019 AsktheBuilder newsletter.

The house I grew up in had a garage floor drain. The concrete floor was sloped like a giant shallow funnel so all water that got on the concrete flowed to the drain. That floor drain never caused any issues in all the years I lived in that home.

My current house doesn't have a garage floor drain. In fact, there's not even one in my all-important mechanical room where the boiler and water heater are located. You know at some point you'll have a leak in this room for goodness sake! I don't think plumbers in New Hampshire know about floor drains. My garage floor is sloped from the back of the garage to the doors.

I live in the snowy and cold Northeast USA where ice and snow are as common in the wintertime as whoopie pies in the grocery store. Water flows to the garage doors and puddles when snow and ice melt from my car and truck. Some seeps under the door and on cold days the garage door weatherstripping freeze to the floor!

It's ridiculous, as are many things in life! A floor drain or two in my garage would prevent this madness.

Silly Building Code Revisions - They're NOT Always Right

It's insane! The building code was altered some time ago prohibiting garage floor drains in certain cities and towns. The reasoning, I'm told, was that spilled gasoline and oil would cause explosions, death, and destruction.

Can you think of the last time in your city or town that you read about or saw on the local TV news that a house was destroyed and people killed by a garage floor drain or gasoline spilled in a garage without a floor drain?

Yeah, I thought so.

garage floor drain ideas

Did you know you can make your own silly TV news graphics like this one? Yes, you'll have eaten, drank, slept in a hammock, went kayaking, played epic games of ping pong against your nemesis, and maybe opened a prize or two before you ever hear about a garage explosion caused by a frivolous floor drain.

Newsletter Response - "Where's the Oil Separator, Tim!"

One or two subscribers who read my newsletter wondered if I had a special way to clean out debris from the floor drain. I've been a master plumber since age 29 and you bet I took that into consideration. Go back up and look at the illustration to see how debris is captured and prevented from entering the drain line.

It's important to realize you need to clean out the debris periodically so it doesn't accumulate to the height of the drain pipe. Look at the following illustration to understand how old floor drains, like the one in the house I grew up in, were piped.

garage floor drain ideas

This is how hundreds of thousands, perhaps millions, of floor drains are piped. You can see that the bottom of the trap can fill with sand and debris. You can't get your hand down the pipe, but you can insert the end of a wet-dry vacuum hose!

You can see old floor drains are much like the p-traps under your bathroom or kitchen sink. It's easy for them to get clogged.

Why Put Traps in Garage Floor Drains?

Traps should be incorporated into garage floor drains to prevent vermin from entering the garage. This is especially true of drains that are piped directly outdoors on the land just outside the garage.

I'd never connect a garage floor drain to a septic system because I don't want any oil or mystery chemicals stored in the garage to have a chance to get into the septic tank.

It's unlikely that a plumbing inspector would allow a garage floor drain to be directly connected to a municipal sewer system. At the very least it should only be connected to a municipal stormwater drainage system.

The traps should be under the garage floor to help prevent them from freezing in cold climates. Water frozen in a p-trap will stop the flow of water out of the garage.

In April of 2019, I had to re-plumb the floor drains in my daughter's garage. The contractor who put them in didn't include a trap and he just ran the drainpipe to the footing drain. This allowed radon to fill the garage like hot air fills a political debate.

garage floor drain ideas

Look at how I installed the drain so it has a vertical riser that allows you easy access to the p-trap. That capped pipe is flush with the concrete floor now that the slab is in place. In addition, I made sure the drain line leaving the floor drain on the right was a straight shot into the p-trap for the same reason.

Quite a few subscribers were wondering where the drain water goes from the garage and if I had installed an oil separator.

The pipe drains to the ground outside about 40 feet from the garage door. I didn't install an oil separator and it's not required by the code.

Let's Apply Common Sense

What do you think the odds are of more than a tablespoon of oil reaching that floor drain on any given day? When was the last time you had a massive oil spill in your garage? If you did, did you clean it up or just hose it outside?

How many total gallons of oil drip from trucks, cars, and heavy equipment up on Mt Desert Island each day where my daughter will live?

What happens to that oil? Is most of it broken down in the soil at the side of the road and/or does a certain amount evaporate over time? Think about where you live. Think about how much oil is spilled on the ground in your town or city each day.

Much/most of the motor oil you put in your car or truck comes from the ground in the first place. It's as organic as it gets. Yes, it almost always needs to be extracted from bedrock, but there are natural seeps.

The point is most responsible people will clean up spilled oil in a garage. Most probably put down old cardboard under a tired engine or transmission.

Lastly, Mother Nature has great healing properties. She can and does clean up oil spills. It may take her more time than you would like, but She gets the job done.

Oil Separators

Let's imagine you're very concerned about getting oil on your land or into the ecosystem. You can install an oil separator as part of your drainage system. You just have to remember to get the oil out by pumping it or scooping it into bottles that you then drive to the recycle center.

It's important to realize the oil in the separator will be underground. You'll be on your hands and knees dealing with it.

If you have strong feelings about garage floor drains and oil, I urge you to spill your thoughts below in the comments. I moderate all comments to prevent SPAM, so it could take a day or two for your comment to appear. I publish all comments that aren't SPAM.

Coast EAL13 Lantern Review

coast eal13

Coast EAL13 Lantern | You can see how petite this powerful lantern is. You can use it for emergency lighting for your car or soft lighting for your campsite or even on your patio in the summer.

Coast EAL13 Lantern - It's Small But Handy For Sure

I've had the opportunity over the years to test many flashlights and lanterns. I even own an official Amtrak lantern used by train crews. I was a conductor on a scenic train in New Hampshire for two summers and had to follow all the FRA rules.

The Coast EAL13 lantern is a very handy one that I recommend in every vehicle you own. It's small enough, only 5 and 3/4 inches tall and 2.5 inches in diameter, to fit in center consoles or glove boxes.

The following pictures tell the rest of the story.

coast eal13

This is the handle you hold it with if you were an old-time RR switchman telling the engineer the switch is safe to travel over.

coast eal13

This is a carabiner on the top so you can hang the lantern from anything that will fit into the spring-loaded clasp.

coast eal13

I know! You want to see how much light it puts out. It's got three levels: low, medium, and blinding. This is on low.

coast eal13

There are five lantern settings. This one just glows red to alert anyone, including space aliens, of danger and they should stop and deposit all cheese coneys they have in their possession. The last setting on the switch is blinking red. This comes in handy if you're broken down on the road.

coast eal13

This dandy lantern has a carabiner on the bottom too! It's specifically made for all users Down Under!

coast eal13

You need three AA batteries to power this bad boy. Remember, always take the batteries out if you're not going to use it for a while.

coast eal13

The lantern will attach and hold itself to any steel or iron surface. It's got four magnets in the base. If you fly an F/A-18 Hornet, don't expect it to hold onto the fuselage.

Did you like this lantern? Speak up in the comments below for goodness sake!

Zircon Breaker ID Review

zircon breaker id

This is the receiver that you touch against the circuit breakers. CLICK or TAP HERE or the image to have one delivered to your home.

Zircon Breaker ID - Works Well

I've had the Zircon Breaker ID for a while, but only today had a reason to put it to the test. It got an A++!

How Does the Zircon Breaker ID Work?

The tool has two parts, a transmitter, and a receiver. The transmitter is the black part you plug into the wall and the receiver is the yellow part of the tool. The receiver is used at the circuit panel.

zircon breaker id

This is the transmitter. You plug this into a regular 120-volt outlet on the circuit you're trying to locate. CLICK or TAP HERE or the image to have this dandy tool in your trembling hands in just hours.

zircon breaker id

The receiver has two LEDS on top. One red and one green. They're so bright they wash out the color in the photo. The tool also has a buzzer, but I couldn't get mine to work even with a new battery. Not to worry, just trust the LEDs. CLICK or TAP HERE to purchase this tool before clicking on and off all your breakers hoping you hear the person inside the house.

zircon breaker id

Here I am scanning the breakers. You need to calibrate the tool by running it up and down all the breakers in the panel. It only takes seconds to do. CLICK or TAP HERE to preserve your sanity and voice. Once you scan all the breakers, you do it one more time. When the tip of the scanner is on top of the breaker that powers the outlet that the transmitter is plugged into, the green LED lights up brighter than your eyes when you get a prize from your best friend!

zircon -breaker id

When you go to store the tool, you insert the receiver into the transmitter and this is what it looks like. CLICK or TAP HERE to order one of these now. You'll not regret it.

 

 

 

Don’t Sweat Copper, Press It

Install Copper Tubing Pipe Tool

You can rent, or sometimes borrow for free, a tool that allows you to install copper tubing pipe with no soldering required! (C) Copyright 2019 Tim Carter

Don’t Sweat Copper, Press It

DEAR TIM: I love reading your column in my local paper. Several months ago you wrote about which plumbing pipe might be better for water lines, copper and PEX. You briefly mentioned a new tool that eliminates the need for soldering copper. I’d like to know much more about this magic method of making leak-proof copper connections. How does this tool work, how fast is it and would you depend on a copper connection that doesn’t rely on solder? Brandy S., Spokane, WA
Brandy’s not the first reader that was intrigued by that quick mention of a newer method to create leak-proof connections between copper water supply tubing and copper fittings. I received several other requests for more information about this newer technology from folks just like you who visited my Ask Tim page at my AsktheBuilder.com website.

For decades, the gold standard of making leak-proof joints when installing copper tubing was solder. As a young plumber back in the 1970s, it’s what just about everyone did. The issue is it takes some effort to prepare the copper, heat it up, melt the solder and allow it to cool down. Soldering also is risky. Ask any seasoned firefighter and he’ll share at least one story of a house fire created by a plumber or DIYer that allowed the torch to set the house ablaze!

As with many things, new ideas and technology debut and disrupt the landscape. Such was the case about seven or so years ago, when I saw the first copper press tool at an editors conference hosted by a major power tool manufacturer. Being a master plumber since age 29, you can bet I zeroed in on this tool like a mosquito lands on my arm each summer evening here in New Hampshire.

WATCH this video to see how FAST the tools work:

The tools are called press tools. The most popular tools have a set of jaws ranging from 1/2-inch all the way up to 2 inches. You may be able to find larger jaws for bigger copper tubing, but I doubt you’d ever need that huge size!

The fittings, like 90-degree bends, tees, couplings, and even valves, have the magic in them that makes the system work. Each fitting has a raised ridge and this formed part of the fitting holds a rubber o-ring.

You cut the copper tubing using a cutting tool that produces a clean cut with no burrs. Never use a hacksaw or if you do, file the edges of the cut to remove all burrs as they might cut the o-ring as you slide the tubing into the fitting.

Once you fully insert the tubing into the fitting, you select the tool jaw that matches the size of the piping you’re working with. You open the jaws, they spring back and lightly clamp around the raised ridge of the fitting and you squeeze the trigger. In three to five seconds, the jaws compress and produce a slight crimping around both the fitting and the tubing.

This compression squeezes the o-ring tightly around the copper tubing creating a leak-proof joint. To do this same operation soldering one end of a fitting to a piece of tubing would take at least two minutes, maybe more.

The cost of the special press fittings is more. While writing this column, I checked the top website I use to buy plumbing supplies and the cost for a 1/2-inch sweat 90-degree fitting was 39 cents. The same size press fitting was $1.83. That’s a difference of $1.44 but think about the time you’ll save!

There’s another huge advantage when it comes to press fittings. You can’t solder a copper pipe that’s got water in it. The steam and water don’t allow the pipe to get hot enough to melt the solder.

You can actually have water flowing out of a pipe at full blast and shut it off using a press tool! All you have to do is purchase a ball valve that has the press fitting built into the valve. You open the valve up so water is squirting out of it, slide the valve onto the pipe, press the end of the valve that’s on the pipe, remove the tool and then close the ball valve to stop the water flow. This is absolute magic when you stop and think about it. Plumbers of old would have given their eye teeth to have this capability to work on dripping pipes!

You may wonder what these press tools cost. They’re expensive as are the jaws. But here’s what you can do. There’s a very good chance your local tool rental store rents them. I know of a plumbing supply house in Maine that will allow you to borrow one for free for one day! They do this as a complimentary service since you buy materials and fittings from them.

These press tools allow you as a DIYer to install copper tubing in your home or to do a repair where otherwise you’d not have the courage to solder. I recently used a press tool to install all the copper tubing that connects my daughter’s new high-efficiency combi boiler to the heating manifolds. This same boiler also is a tankless water heater and I used the press tool to make all the connections of the copper water lines. I saved countless hours and didn’t have one leak.

Press it, don’t sweat it!

Column 1330

December 1, 2019 AsktheBuilder Newsletter

Is this your first rodeo with me? Your first newsletter? Saddle up!

If you've rode with me before, no matter how long, you know things can get a little dusty. The chow wagon is filled with pecan pie, so we're going to eat good tonight!

Firing Up the Noritz Combi Water Heater Boiler

This past Monday, I fired up the fantastic Noritz Combi water heater boiler at my daughter's new house with the help of Paul Tibbetts. Paul is a Noritz rep and he travels around much of New England making sure all is well with the magic machines from Noritz.

Paul Tibbetts Noritz Combi

CLICK or TAP HERE to see many many more photographs of the install process.

Paul's hand, although blurred, is pointing at the heat exchanger. It's about the size of a loaf of bread!

It's important for you to realize this crazy machine can produce 199,000 Btus in that little stainless steel box!

We had no leaks at all in the 6,000 feet of Uponor hePEX tubing that runs under the floors. CLICK or TAP HERE to understand why I used this amazing plastic tubing to make all the floors in the house toasty warm.

I'm stunned by how quiet the Noritz combi boiler is. This boiler is in a small closet that's in the entrance hall of the house. It's centrally located and even with the door off the closet, you could barely tell it was running. Amazing!

BOTTOM LINE: I can't say enough good things about this Noritz combi boiler. Another key point is it's a modulating boiler. This means the fire inside the heat exchanger can range anywhere from about 20,000 Btus, all the way up to 199,000 Btus. The boiler only sips as much energy as is needed to handle the demand for either heat in the house or domestic hot water to shower, bathe, clean or wash the car in the garage.

Yes, I installed a special hot/cold water faucet in the garage so in the winter my son-in-law can wash his car with refreshing HOT water! Oh, you wonder about the water and where does it go?

Why yes, I made sure there was a floor drain under each car and the concrete floor in the garage is sloped like two giant shallow funnels so the water flows to the floor drains! This means all snow melt will go to the drain and not flow towards the garage door!

If you heat with a boiler and it's time to get a quote for a new one, CLICK or TAP HERE and tell the contractor you want the Noritz NRCB.

SHOP AT AMAZON

If you're shopping at Amazon.com for Christmas presents, please consider using my affiliate link. CLICK or TAP HERE to help make sure this newsletter keeps coming to you.

Testing TrueWerk

Three weeks ago, I was asked to test some clothing. I received a handsome vest, a hoodie and two pairs of pants from TrueWerk. The vest and hoodie are made from the same fabric and have the same look and cut. To picture the vest, just look at the photo below and imagine no sleeves and no hood.

TrueWerk Jacket

Both the vest and the hoodie have become my GO-TO favorites. The fabric of both is medium-weight and they're so soft! They both have strategic pockets for smart phones and the side pockets are nice and spacious. The fabric has some stretch to it, but not much.

These would make GREAT GIFTS for anyone that wants stylish clothing.

CLICK or TAP HERE to see the specs on the hoodie. Keep in mind the fit is a little sculptured so you may want to get the next size up if a normal fit is just a bit snug for you.

The pants that were sent to me were a little long so I'm taking them to a local seamstress to have them hemmed correctly. I already tried them on and they fit perfectly. They're made from a unique smooth synthetic fabric.

I'll report back on these once I get to wear them.

Tom's White Brick Troubles

Look at this photo. Do you know what's going on?

It's not whitewash. But if you do want to know how to do traditional REAL whitewash, CLICK or TAP HERE.
Tom's White Bricks

Tom, who resides in Wallace, NC, sent in that photo and wrote:

"Tim, my bricks have a white chalky look to them, and it does not power wash off. What can I do to get rid of it?"

Well, the first mistake Tom made was trying to fix the problem BEFORE researching it. Power washing it made it WORSE.

Do you know why power washing made it worse?

CLICK or TAP HERE and read as MANY of my past columns about this and for goodness sake, be sure you WATCH MY VIDEOS about this white menace!

That's enough for a Sunday.

A pretty big snow event is about to happen here in New Hampshire. It could be our cover snow. This means I'll not see the grass or earth until April as the ground will have snow covering it for the next four months!

Tim Carter
Founder - www.AsktheBuilder.com
Buy Certified Organic Cleaner - www.StainSolver.com
Morse Muff Man - www.W3ATB

Do It Right, Not Over!

P.S. What do you think is the best exterior house paint? Think about what paint really is before answering. CLICK or TAP HERE to see what I'd use on your home if you hired me.

November 29, 2019 AsktheBuilder Shopping Reminder

If you're a new subscriber in the last five days, this is a very unusual edition of my newsletter. Two days from now you'll see a normal one.

If you've received more than one issue in the past, then you know this is an out-of-the-ordinary message!

Black Friday at Amazon.com

Today is historically a massive shopping day online. There are amazing deals to be had. If you're shopping at Amazon.com, you can really HELP keep this newsletter coming to you by using my affiliate link. CLICK or TAP HERE to start shopping at Amazon.com.

When you shop using that link, I get a tiny slice of the sale price of the item for brokering the deal. It doesn't cause your price to go up. What happens is Jeff Bezos, the founder of Amazon and richest person in the world, gets less money he can use to fuel up his private jet fleet.

Do you know why so may businesses are IN YOUR FACE about Black Friday? Why they are DESPERATE for you to buy their item(s)?

Do you know why you see things going on sale EARLIER and EARLIER each year?

It's actually quite interesting.

Businesses know that you have a limited budget for Christmas gifts. The businesses want to stake their claim on part of your limited money so they aggressively court, seek, pursue your sweet moola.

They want to get their SLICE of it before you run out.

It's that simple.

I want to thank you in advance should you decide to help out Ask the Builder by using my link into Amazon.com.

The revenue I receive from this monster company goes a long way to help pay for the costs of running my business.

The more you help me, the better guarantee you'll have of AsktheBuilder.com and THIS NEWSLETTER being here when you most need it! CLICK or TAP HERE to use my affiliate link to start shopping at Amazon.

My Thanksgiving was pretty quiet but enjoyable. It's my favorite meal of the year and the brined turkey was the best ever. It was so moist, I thought I might drown eating each bite!

I'll be back on Sunday with some juicy leftover columns and tips that will absolutely save you money as we now march towards Christmas!

Tim Carter
Founder - AsktheBuilder.com

Do It Right, Not Over!

P.S. Brining a turkey is really easy. It makes all the difference in the world with respect to how moist the meat is.